4.23 Two kilograms of water are contained in a piston/cylinder (Fig. P4.23) with a massless piston loaded with a linear spring and the outside atmosphere. Initially the spring force is zero and P₁ = P₁ = 100 kPa with a volume of 0.2 m³. If the piston just hits the upper stops the volume is 0.8 m³ and T = 600°C. Heat is now added until the pressure reaches 1.2 MPa. Find the final temperature, show the P-V dia- gram and find the work done during the process.

4.23 Two kilograms of water are contained in a piston/cylinder (Fig. P4.23) with a massless piston loaded with a linear spring and the outside atmosphere. Initially the spring force is zero and P₁ = P₁ = 100 kPa with a volume of 0.2 m³. If the piston just hits the upper stops the volume is 0.8 m³ and T = 600°C. Heat is now added until the pressure reaches 1.2 MPa. Find the final temperature, show the P-V dia- gram and find the work done during the process.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Show solutions pls
Q2// The initial state of air is 120 KPa and 320 K with volume 0.11 m3 which is compressed isothermally until reaching its half volume and after that it is compressed at constant pressure until reaching 4 volume of the initial volume. Find the pressure, the volume and temperature in each state.
2.43 A steel tank contains 6 kg of propane (liquid + vapor) at 20°C with a volume of 0.015 m. The tank is now slowly heated. Will the liquid level in- side eventually rise to the top or drop to the bottom of the tank? What if the initial mass is 1 kg instead of 6 kg?
This fixed-mass system undergoes an isothermal, quasi-equilibrium process from state 1 to state 2. The initial volume is 1 m^3. The mass inside the system is an unspecified ideal gas. Initial Pressure starts at 1000 kPa and the final pressure goes to 100 kPa. Find the change in specific internal energy the work done on the system and the heat transfer in KJoules.
Q2: A cylindrical tank contains air, oil and water, as shown in the Fig; the air is under gage pressure P= 2 bar. Find the exit velocity. OP Air Oil specific gravity = 0.8 2 m Water 5 m exit 2 cm
3.30 Using the tables for water, determine the specified property data at the indicated states. In each case, locate the state on sketches of the p-v and T-v diagrams. WP a. At p = 3 bar, v = 0.5 m³/kg, find T'in °C and u in kJ/kg.
B/ Water in a rigid, insulating tank is set in rotation and left. Water comes to rest after some time due to viscous forces. Considering the tank and water to constitute the system answer yes or no. (i) Is any work done during the process of water coming to rest? (ii) Is there a flow of heat? (iii) Is there any change in internal energy (U)? (iv) Is there any change in total energy (E)?
As shown in the figure below, air is contained in a vertical piston-cylinder assembly such that the piston is in static equilibrium. The atmosphere exerts a pressure of 14.7 lbf/in.² on top of the 6-in.-diameter piston. The absolute pressure of the air inside the cylinder is 20 lbf/in.². The local acceleration of gravity is g = 32.2 ft/s². Determine the mass of the piston, in lb. Mpiston = Determine (a) the mass of the piston, in lb, and (b) the gage pressure of the air in the cylinder, in psig. lb p(gage) = i Pa 14.7 lbf/in.² g=32.2 fus² Determine the gage pressure of the air in the cylinder, in psig. psig Di Air Pair
Please don't provide handwritten solution ...
There's a copper calorimeter container with the mass 0.2 kg and has 0.32 kg of H2O and also 0.036 kg of ice (thermal equilibrium at atm). If we drop 1.5 kg of lead at a temperature of 200 Celsius into calorimeter container, find the final temperature (in Celsius). Please show work Lead=131J/kgK Copper=390J/kg.K H2O = Cw = 4190 J/kg.K & LF = 3.34 x 105 J/kg
Please Use Energy Method d/dt (T+V) where T is KE and V is PE
Describe a closed system with a moving boundary?