Po Q3.A frictionless piston/cylinder contains saturated water at 35°C. The piston cross-sectional area is 0.06 m² and has a mass of 4kgs. Initially, the piston resting on the stops enclosing a volume of 0.03 m³. To raise this piston against atmospheric pressure, a pressure of 300 kPa has to be applied. On moving the piston upwards, it will encounter a linear spring when the contained volume is 0.075 m³. To deflect this spring 1 m, the force required is 360 kN. If the final pressure is 7 MPa, determine a) the final state of water, and b) the work done during the process. H₂0

Po Q3.A frictionless piston/cylinder contains saturated water at 35°C. The piston cross-sectional area is 0.06 m² and has a mass of 4kgs. Initially, the piston resting on the stops enclosing a volume of 0.03 m³. To raise this piston against atmospheric pressure, a pressure of 300 kPa has to be applied. On moving the piston upwards, it will encounter a linear spring when the contained volume is 0.075 m³. To deflect this spring 1 m, the force required is 360 kN. If the final pressure is 7 MPa, determine a) the final state of water, and b) the work done during the process. H₂0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Fluid Mechanics
Q4/Find the work done by the steam if 300-L cylinder contain 500 g of steam at 400Kpa now heat transferred to the steam until the temperature is 300 C at constant pressure.
Please solve with detailed and clear solutions
Q3: Calculate the applied force to move the process Envierment W-100 Ib -0.2 Process W-100 Ib μ0.2 Refinery W-100 lb μ-0.1 1 P
3. A 10 t° tank contains gas at a pressure of 500 psia, temperature of 85-F and a weight of 25 pounds. A part of the gas was discharge and the temperature and pressure changed to 70-F and 300 psia, respectively. Heat was applied and the temperature was back to 85 F. Find the final weight, volume, and pressure of the gas?
Air is contained in a frictionless piston-cylinder assembly as shown below. The initial equilibrium position is subjected to atmospheric pressure of 100 KPa. The mass of piston and weight together is 200 kg. The piston has a diameter of 0.452 m. The initial temperature of the gas in the container is 800 K. Take C, = (7/2) R and Cy = (5/2) R, calculate the following: (a) force exerted by the piston, weight, and the atmosphere in N (b) total pressure of air in the container in kPa (note: at initial equilibrium position, the Peas = Pop) (c) total moles of air in the container (assume air behaves ideally)
Show complete solution with t-s diagram please.
A wire ring of radius 6 cm is rested flat on the surface of a liquid and then slowly raised. The pull required is 0.06 N more before the film breaks than it is after. What is the surface tension of the liquid? Neglect the thickness of the ring.
Graw 1 Q A The force generated by a spring is given by F= kx where k is the spring constant, and x is the deflection of the spring. The spring shown in the figure has a spring constant of 9.5 kN/cm. The pressures are P-5000 kPa, P₂=10000 kPa, and P3 = 1000 kPa. If the piston diameters are D=8 cm and D2-3 cm, how far will the spring be deflected? Z Spring- The spring will deflect 1.717 cm. 2 W D₁ S 309 F2 X #3 E D 80 F3 $ 4 C 888 F4 R 25 % V MA FS T U N * 00 8 J DII - M ( 9 K DD F9 O ) V S 0 J L T' P
Q2 Calculate the density of the air in a room whose Dimensions are (4 m, 5 m, 6 m) and have mass 140 kg. AIR 5m P= 100 RPa T= 25°C
A frictionless piston/cylinder assembly A shown in the figure is connected by a thin pipeline with a valve to a rigid tank B. The volume of tank B is 1.0 m³, and the cross-sectional area of the piston is Aa = 1.2 m?. Initially (state 1) the valve is closed, 3 kg of argon is enclosed in the piston/cylinder assembly, mĄ1 = 3 kg, and there is no argon in the tank, mg,1=0. The initial temperature of the argon is TĄ1 = 50°C and the initial volume of the gas enclosed by the piston cylinder is VA1 = 1.5 m?. The valve is slowly opened allowing argon to flow into the tank. The valve is then closed when the piston just touches the stops but does not exert a force on the stops (state 2). At state 2, the temperature and pressure throughout the tank and piston/cylinder system are equal (Pa2 = P8,2 and Ta2= T82). The height from the bottom of the cylinder A to the top of the stops is htops = 0.5 m. The volume of the stops can be assumed negligible. Treat argon as an ideal gas. a) Determine the…