B/ Water in a rigid, insulating tank is set in rotation and left. Water comes to rest after some time due to viscous forces. Considering the tank and water to constitute the system answer yes or no. (i) Is any work done during the process of water coming to rest? (ii) Is there a flow of heat? (iii) Is there any change in internal energy (U)? (iv) Is there any change in total energy (E)?

B/ Water in a rigid, insulating tank is set in rotation and left. Water comes to rest after some time due to viscous forces. Considering the tank and water to constitute the system answer yes or no. (i) Is any work done during the process of water coming to rest? (ii) Is there a flow of heat? (iii) Is there any change in internal energy (U)? (iv) Is there any change in total energy (E)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a mass-spring system. The spring has a spring constant of 2.35e+3 N/m. On the end of the spring is a mass of 0.840 kg. At the moment that the block is at the system's equilibrium position, it has velocity 2.24 m/s. What will be the maximum displacement of the block from equilibrium if we ignore all friction. Please enter a numerical answer below. Accepted formats are numbers or 'e' based scientific notation e g. 0.23.-2. 16, 523-8
A torque of 2 N-m is necessary to rotate a paddle wheel at a rate of 20 rad/s.The paddle wheel is located in a rigid vessel containing a gas. What is the net work injoule done on the gas during 10 minutes of operation?
8. During the drive, you can take fresh air using the conditioning system available in the automobile. However, you should slightly open (about 1 cm) your window for the exhausting some air, according to the mass balance principle. If you open your window completely, the intake of fresh air and exhaust of polluted air will deteriorate. Based on this information, what do you think about pressure balance? A) Pautomobile Poutside B) Pautomobile = Poutside C) Pautomobile > Poutside D) Pautomobile SPoutside 9. Which temperature measurement device is mostly used in industry? A) Gas thermometry B) Thermocouples C) Bimetallic thermometers D) Thermal Camera 10. Which measuring instrument should be preferred to convert qualitative measurement with thermochromic liquid crystals to quantitative data. A) Resistance Temperature Detector B) Thermocouples C) Bimetallic thermometers D) Thermal Camera 11. Which of the temperature measurement technique is used for visual warning of certain temperature…
P2 Explain the application of the first law of thermodynamics to appropriate systems
A body of mass 20 kg falls freely in vacuum. It has fallen through a vertical distance of 50 m. The gravitational acceleration may be assumed as 10 m/s?. What is the thermodynamic work done by the body?
In an engineering system, air passes through two sequential processes. These processes Information about it is given below. Process 1-2: Polytropic compression, n = 1.3, P1=100 kPa, v1 =0.04 m3 /kg v2 =0.02 m3 /kg. Process 2–3: v3 = constant pressure process up to v1. In the light of this information, 1)draw the P-v diagram of the system. 2)Work per unit air mass in kJ/kg set as.
Momentum Transfer. Answer the ff.
0.56 kg of water in a piston cylinder device as shown initially the water is at T, = 120 °C with volume V, = 36 L (State 1). Heat is then added such that all the water in the cylinder is saturated vapor and the piston just touched the spring without exerted any force on the spring (State 2). Then additional heat is added to the system such that the temperature is T, 600 °C and the pressure is P,= 400 kPa (State 3). 3 Po 3 1) Find the total work (from state 1 to state 3, in kW). O 147.73 2) O Not listed Qin 111.16 133.48 107 23 156.11 125.24 2) Find the total heat transfer for the process (from state 1 to state 3, in kW). 1424.6 O Not listed O 1486.0 O 1585.4
20. Two objects are connected to each other by a rope over a pulley as in the figure. The 8.00 kg and mp = 11.0 kg. If initially ma is at rest 1.36 m from the masses are mA= edge of the table, how long does it take to reach the edge of the table if the system is allowed to move freely (i.e. with no friction)? Mg (c) 1.97 s (a) 12.3 s (d) 0.692 s (b) 0.413 s (e) 5.38 s
Nhand,A 75 N ma = 3 kg %D VA = 8 m/s Block Block Block Block B A Hx = 0.4 %3D 2 m Ax Note: Diagram is not drawn to scale A hand pushes block A (m,= 3 kg) with a constant force Nand. A= 75 N for a distance Ax 2 m along a (mostly) frictionless table such that it speeds up from rest and is traveling at a speed of 8 m/s after it slides over a rough section of the table (H = 0.4). Block A then collides with a more massive block B (mg = 6 kg) that is initially at rest. Find the speed of block A after it has been released by the hand and just before the rough section of the table. A) 10 m/s B) 20 m/s C) 30 m/s D) 40 m/s E) 50 m/s O A O B O D O E
Consider the mass-on-a-spring system as shown in the figure below. The spring has a spring constant of 1.86e+3 N/m, and the block has a mass of 1.39 kg. There is a constant force of kinetic friction between the mass and the floor of 4.71 N. Starting with the spring compressed by 0.117 m from its equilibrium position, how far will the block travel once it leaves the spring? (Assume that block leaves the spring at the spring's equilibrium position, marked x=0 in the figure. Give your answer as the distance from the equilibrium position to the final position of the block.) Hint: How much work must friction do in order to bring the mass to a stop? How much distance is required for friction to do this work? Enter answer here www.m X = 0 Please enter a numerical answer below. Accepted formats are numbers or "e" based scientific notation e.g. 0.23, -2, 1e6, 5.23e-8 Image size: S M L Max m
Discuss all the laws of thermodynamics (Zeroth, first, second and third) and give their physical significance.