A rigid tank of volume 10 m³ initially contains saturated water vapor at a temperature of 120 °C. Steam at a pressure 1.2 MPa and a temperature of 400 °C enters the tank through a valve in steam line that is connected to the tank until the final pressure in the tank is 800 kPa, at which time the temperature is 200 °C. All kinetic and potential energy effects can be neglected. A schematic of the problem and properties at all state points except state 1 are shown in the figure below. All of the properties at state 2 and the inlet state i are provided on the figure.

A rigid tank of volume 10 m³ initially contains saturated water vapor at a temperature of 120 °C. Steam at a pressure 1.2 MPa and a temperature of 400 °C enters the tank through a valve in steam line that is connected to the tank until the final pressure in the tank is 800 kPa, at which time the temperature is 200 °C. All kinetic and potential energy effects can be neglected. A schematic of the problem and properties at all state points except state 1 are shown in the figure below. All of the properties at state 2 and the inlet state i are provided on the figure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state temperature pressure p2.__________ (kPa)
A cylinder is fitted with a freely movable piston of area 1.20e-2m^2 and negligible mass. The cylinder below the piston is filled with a gas. At state 1 the gas has volume 1.50e-3m^3, pressure 1.02e5Pa, and the cylinder is in contact with a water bath at a temperature of 0.0C. The gas is then taken through the following four step process. - A 2.50kg metal block is placed on top of the piston, compressing the gas to state 2, with the gas still at 0.0 C. - The cylinder is then brought in contact with a boiling water bath, raising the gas temperature to 100C at state 3. - The metal block is removed and the gas expands to state 4 still at 100C. - Finally, the cylinder is again placed in contact with the water bath at 0C, returning the system to state 1. a) Determine the pressure of the gas in state 2. b) Determine the volume of the gas in state 2. C) Determine the volume of the gas in state 4. Answer all parts, ABC
A monatomic ideal gas is compressed isothermally from a volume of 2.0m^3 to 1.0 m^3. The initial pressure is 20 kPa. a. Find the work done on the gas from initial state to final state. b. Find the change in the internal energy of the gas. c. Find the amount of heat exchanged.
Take time but solve all ßolutions with handwriting
Consider a turbine operating at steady-state with the operating conditions shown in the figure. Superheated water vapor enters the turbine with a mass flow rate of m = 5 and superheated water vapor exits at p2 and T2. Ignoring stray heat transfer and kinetic and potential effects: a. Calculate the net power of the turbine, Wr, in kW b. Calculate the entropy produced in kW/K All state properties needed to solve are provided below: State T (°C) p (bar) h (kJ/kg) s (kJ/kg-K) (1 1 240 10 2920.4 6.8817 Wr 2 160 3 2782.3 7.1276 P1 = 10 bar T = 240 °C = 3 bar (2) P2 T2 = 160 °C
2. A piston-cylinder assembly with stops (see figure) contains 1.54 kg of water initially occupying a volume of 1.25 m at a pressure of 1 bar (State 1). As the water in the assembly is heated, the pressure and temperature in the system remain constant until the piston contacts the stops. In this position (State 2), the quality, x2, is determined to be 92%. Heat continues to be added to the system at a constant volume until the system reaches a pressure of 1.5 bar (State 3). Determine the following quantities: а. X b. V2 (m2) C. W13 (kJ) d. Qu (kJ) e. Plot the results on a P-v diagram, labelling relevant P, T, and v values.
Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state temperature T2.__________ (K)
Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state pressure p2.__________ (kPa)
I am getting lost in this practice problem for thermodynamics - thank you! Air at 100 kPa and 280K is compressed steadily to 600 kPa and 400K in an air compressor. The mass flow rate of air through the compressor is 0.02 kg/s and the compressor a heat loss of 16 kJ/kg from the compressor occurs. Assuming steady state steady flow conditions and ideal gas behavior (with constant specific heats, Cp=1.009 kJ/kgK, R=0.287 kJ/kgK, determine: a) The necessary power in put to the compressor(kW).b) The volumetric flow rate of air at the exit of the compressor (m3/s).
A rigid tank of volume 10 m³ initially contains saturated water vapor at a temperature of 120 °C. Steam at a pressure 1.2 MPa and a temperature of 400 °C enters the tank through a valve in steam line that is connected to the tank until the final pressure in the tank is 800 kPa, at which time the temperature is 200 °C. All kinetic and potential energy effects can be neglected. A schematic of the problem and properties at all state points except state 1 are shown in the figure below. All of the properties at state 2 and the inlet state i are provided on the figure. Initial State in Tank T₁-120 °C, Sat. vapor u₁=? kJ/kg V₁=? m³/kg Pi=1.2 MPa, Ti-400 °C hi-3261.3 kJ/kg V=10 m³ Final State in Tank T: 200 °C, P₂-800 kPa u₂= 2631.1 kJ/kg v₂=0.26088 m³/kg Qout For Question 6: The initial specific internal energy, u1, of the saturated vapor in the tank in kJ/kg is
Air as an ideal gas is contained in a piston/cylinder system constrained by a non-linear spring. Initially the gas in the cylinder is at 100 kPa, which is balanced by the atmospheric pressure outside of the cylinder (the weight of the piston is negligible). The force on the spring at the start is zero. The spring force is F=kx². k=600. kNt/m². The cross-sectional area of the piston is 1 m², the initial volume is 1 m³, and the initial temperature is 300 K. Heat is added until the volume of the gas has expanded to 1.5 m³. Find: (a) The work done by the gas on the face of the piston (kJ). (b) The final temperature (K). (c) The amount of heat added (kJ). Hint: This problem is easiest if you calculate the spring work and the atmospheric work separately. Air V₁=1.0 m³ Piston Area = 1.0 m² T₁=300 K P₁=100 kPa Atmospheric P on upper piston face= 100 kPa
An ideal gas is compressed from a volume of V, = 6.00 L to a volume of V, = 3.00 L while in thermal contact with a heat reservoir at T = 295 K as in the figure below. During the compression process, the piston moves down a distance of d = 0.145 m under the action of an average external force of F = 21.0 kN. (a) Find the work done on the gas. kJ (b) Find the change in internal energy of the gas. k) (c) Find the thermal energy exchanged between the gas and the reservoir. kJ (d) If the gas is thermally insulated so no thermal energy could be exchanged, what would happen to the temperature of the gas during the compression? O The temperature would decrease. O The temperature would remain constant. O The temperature would increase.