A circular rod and a 3/8-in.-thick rectangular bar are both made of a plastic material that has an elastic modulus of E= 2.7 GPa and a Poisson's ratio of v=0.4. The rod and the bar are initially the same length L. After a particular load is applied, the 3.5-in.-wide rectangular bar is elongated by some amount AL and its width is reduced by 0.093 in. If the 1.25-in. diameter rod is stretched by the same amount AL, determine its change in diameter. Expansion is positive, while contraction is negative. Circular Rod Rectangular Bar Answer: Ad= i original diameter original width in. L 1 ΔΕ

A circular rod and a 3/8-in.-thick rectangular bar are both made of a plastic material that has an elastic modulus of E= 2.7 GPa and a Poisson's ratio of v=0.4. The rod and the bar are initially the same length L. After a particular load is applied, the 3.5-in.-wide rectangular bar is elongated by some amount AL and its width is reduced by 0.093 in. If the 1.25-in. diameter rod is stretched by the same amount AL, determine its change in diameter. Expansion is positive, while contraction is negative. Circular Rod Rectangular Bar Answer: Ad= i original diameter original width in. L 1 ΔΕ

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Wire BC has a diameter of 0.10 in. And its material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle D if the pull on the handle is slowly increased and reaches the magnitude of P = 655 lb. o (ksi) 40 pulg 80 70 B 50 pulg - 30 pulg € (pulg/pulg) 0.007 0.12
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 20 x 10-3 mm while those at CD decrease 80 x 10-3 mm in the 250-mm-gage length. Using E = 180 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 50 mm, b 120 mm, and c = 70 mm. gage length a mm B b mm c mm
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 103 mm while those at CD decrease 80 x 10 ³ mm in the 230-mm-gage length. Using E = 150 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b 130 mm, and c = 90 mm. gage length a mm b mml c mm
Solve Clearly!!!!z,
A steel wire (E = 200 GPa) of diameter d = 1.0 mm is bent around a pulley of radius Ro= 400 mm (see figure below). Ro a. What is the maximum stress in the wire? b. Does the stress increase or decrease if the radius of the pulley is increased?
Homework #6 Problem 1. A steel alloy core is bonded firmly to the copper tube to form the shaft shown. The materials have the shear stress-strain diagrams are shown in the figure. a) If the total applied torque is 15 kN.m, determine the torque resisted by the core and tube. b) What is the maximum elastic torque that can be applied to the shaft? What is the corresponding maximum shear strain in the shaft? c) What is the maximum torque that one can apply to the shaft? 100 m 60 mm +(MPa) 180 450 mm 15 KN-m 0.0024 (MPa) Steel Alloy 36 0.002 Copper Alloy (rad) y (rad)
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.21 in.? and an elastic modulus of 2350 ksi. Bar (2) has a cross-sectional area of 1.032 in.? and an elastic modulus of 4100 ksi. Assume L1=20 in., L2=49 in., Q=7.1 kips, P=2.9 kips, and R=12.9 kips. Determine the horizontal deflection of end C relative to end A. P (1) (2) C В L1 L2 Answer: uc/A in. %3D