A solid plastic rod has a diameter of d = 22 mm and a length of L = 600 mm. An axial load of P = 21 kN is applied to the rod as shown. The elastic modulus is E = 2.3 GPa and Poisson's ratio for this material is v=0.37. Determine the magnitude of the change in the rod diameter Ad for the given load. Answer: Ad=i mm

A solid plastic rod has a diameter of d = 22 mm and a length of L = 600 mm. An axial load of P = 21 kN is applied to the rod as shown. The elastic modulus is E = 2.3 GPa and Poisson's ratio for this material is v=0.37. Determine the magnitude of the change in the rod diameter Ad for the given load. Answer: Ad=i mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum pipe (modulus of elasticity 10.1x10^6 psi) is fixed at one end and is subjected to a tensile load of 127.5 kips at the free end. The length and cross-sectional area of the pipe is given as 36.1 in and 9.11 in^2. Assume that the aluminum pipe has clockwise torques (100 lb-in) acting at the midpoint and free end of the pipe. (a) Derive the element stiffness matrix
The rigid horizontal slab is attached to two identical copper rods. There is a gap Δ = 6.18 mm between themiddle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 81°C. Use the following data:
A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given E = 2 x 105 N/mm² and E= 1.2 x 105 N/mm².
For a metal rod of 12 mm diameter and 22 cm length; a) When exposed to a load 2000 kg, it elongated by 1.2 mm. Find this load the actual stress in MPa and the true strain message. b) The tool diameter, which is extended by 8.3x10^-2 mm under a load of 870 kg, has been measured as 11.998 mm. Calculate the Poisson ratio of the material.
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure below. Axial loads are applied at the positions indicated. Find the maximum value of P (Newton) that will not exceed a stress in steel of 147 mPa. in aluminum of 94 mPa, or in bronze of 109 mPa. The final answer should have 2 decimal places where cross-sectional area of Steel = 513 mm2; Aluminum = 416 mm2; Bronze = 207 mm2 Length of Steel = 3.0 m; Aluminum = 2.7 m; Bronze = 1.8 m
Stress (MPa) 2000 Using the stress-strain results shown in the figure, determine the 0.2% offset yield strength and the strain at the onset of necking. Indicate both on the graph and write the value along with units in the space provided. MPa 2000 1000 1000 0.000 0.005 0.010 0.015 Strain 0 0.000 0.020 0.040 0.060 0.080 Strain 100 300 Yield Strength units: 200 Stress (10³ psi) Strain at the onset of necking: units:
1.2 A hollow steel rod has a length of 1m. The outside diameter of the rod is 0.2m and the inner diameter is 0.18m. The rod is compressed axially with a load of 200kN. The modulus of elasticity and the Poisson's ratio of the rod are 200GPa and 0.3 respectively. Determine the increase in outside diameter of rod using the calculated value of decrease in length. (The decrease in length=0.17mm)
Mechanics of deformable bodies -Write complete solution
The beam shown in Fig QB1 is made from aluminium tube of rectangular cross-section having a vertical height of 50mm, a horizontal width of 30mm and a wall thickness of 3mm. The dimensions given in the figure are in millimetres. The yield stress in tension is 200MPa; Young's modulus is 71GPa. Determine: an expression for the bending moment at every point in the beam and draw the bending moment diagram a) b) c) d) the maximum bending moment the maximum longitudinal stress the maximum vertical deflection 200 3kN 200 1kN 100
A load of 1000 N is applied as shown in figure, given cross-sectional area of bar 1 & 2 is 100 mm² & 80 mm2, young modulus of elasticity E₁ = 120 GPa, E₂ = 150 GPa. Calculate the minimum normal stress (in MPa) (1) (2) P= P= 1000 N
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are 0 = 100MPa, oy = 35 MPa, and Txy = 70MPa, acting in the directions shown in the figure. Oy Txy Ox
A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a tensile axial force P, its diameter is decreased by 0.018 mm. Assume the Poisson’s ratio to be 0.33. Determine the value of loads P and its axial deformation. P = ? N δ = ? mm