A cantilever sheet pile is 8.2 m long with depth of embedment of 3.2 m. Angle of friction of the soil supported by the sheet pile is 34° and has a unit weight of 1.91 g/cc. There is water table below the base of the sheet pile. SIT AA. a. Compute the active force acting on the sheet pile. b. Compute the passive force acting on the sheet pile. c. Compute the theoretical passive force that must be mobilized to ensure stability.

Q: Jse commands (rectangle, mirror) and List he commands to draw the following drawing start from a…

A:

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: Draw the projections (Top, Front, Side) with Dimensions for this objects

A:

Q: What is this called?

A: Chisel

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: 10 + 5x < 6+3x

A:

Q: How can I find GH, EG and FH

A:

Q: Subject bussiness communications (civil engineering ) draw any bussiness letter

A: Business letter-  It is a formal document which is sent from one company to another or from a…

Q: 1.5 1.7 2.3 3.0 2.5 1.4 2.0 1.0 1.1 2.6 1.8 2.0 3.2 1.4 0.9

A: ASKED: To determine the number of trucks (of given capacity) required to fill the given grid. Given,…

Q: For the given structures, determine the degree of indeterminacy. 7. A 7

A:

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: For the given structures, determine the degree of indeterminacy. 8. 8

A: Solution : The number of external reactions ( r ) = 9  The number of members ( n ) = 2  These values…

Q: what is ytm

A: There are different type of the calculation done in the funds. The funds can increase or decrease…

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: a) top most, hef tmost

A: X = 1.5 cm Y = 5.48 cm

Q: You are appointed as an officer of Occupational Safety to investigate the incident happened during…

A: Officer of Occupational Safety is responsible for 1) Enforcing safety policies, 2) Conducting audits…

Q: +y") dx ly

A:

Q: For the given structures, determine the degree of indeterminacy. 1. ♫

A: This question is related to the Structure analysis

Q: The representation of the hinge lines of the glass box in a drawing are known as lines. ....** .....…

A: The glass box concept is used in orthographic projection. When the glass box is visualized, then…

Q: What are the commonly available switch actions?

A: Commonly available switch actions? ON-OFF, SPST. SPST = Single Pole, Single Throw.  (ON)-OFF,…

Q: How do I get the support forces

A: The x and y are the vertical and horizontal distances: x=12cos60=6 fty=6sin60=5.196 ft

Q: Determine external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+1+2=6

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 4)…

A: 1. Deactivate the voltage source (V1):Set the voltage source V1 to zero (0 V). This means the…

Q: -0129 -077 R26

A:

Q: Dipper is another word for bucket. ) True False

A: A word or phrase that is exactly the same as another word or phrase in the same language. for…

Q: * .I don't like this," said Ali“ Correct Incorrect

A: The correct punctuation marks for this be like this "I don't like this," said Ali.

Q: 12 13 12 13 14 10 Which tools that can be used to :4 draw the following shape in .AutoCAD R5 R10 R12…

A: To draw the given shape we will require the following command necessarily :- Dimension, line or…

Q: Define phreatic surface.

A: The term phreatic is used in hydrology and the earth sciences to refer to matters relating to ground…

Q: Define Torsion,

A: Torsion: The twisting of a material by the loading of external forces i.e couple which produces…

Q: There are 7 dimension commands in AutoCAD. True False

A: These are the dimension commands available in AutoCAD:

Q: as face pen uut area dhers is defined

A: Stress is defined as the ratio of force upon area . Stress unit example N/mm2 , KN/m2Stress=Force…

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.