A Buck converter is fed from a DC source of 150 V, and has a load of 6000 N connected at its output. The converter implements an IGBT as a controllable switch, whose on-state voltage drop is 2.11 V. If the IGBT is operated at a switching frequency of 114 kHz and a duty cycle of 26%, then the average output voltage is V, the rms value of the output voltage is V, and the input resistance seen by the DC source is Q.

A Buck converter is fed from a DC source of 150 V, and has a load of 6000 N connected at its output. The converter implements an IGBT as a controllable switch, whose on-state voltage drop is 2.11 V. If the IGBT is operated at a switching frequency of 114 kHz and a duty cycle of 26%, then the average output voltage is V, the rms value of the output voltage is V, and the input resistance seen by the DC source is Q.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three phase full converter is supplied by a phase voltage V5-120V, 50 Hz. The rectifier supplies a resistive load R=100 Q. Suppose that the average output voltage is 40 % of the maximum possible average output voltage. The delay angle a would be equal to: Select one: O a. 44.42deg O b. 88.42deg O c. 66.42deg O d. 22.42deg TOSHIBA
Calculate the theoretical output DC voltage of the center-tapped full-wave rectifier circuit and compare it with measured value. For the capacitive filter, obtain the theoretical values of the DC output voltage and the ripple voltage and compare these values with the measured quantities. Determine also the practical and theoretical values of the ripple factor.
The half wave rectifier is supplied with 240V, 50Hz signal. Assume the number of turns in the primary to secondary ratio is 7:2. Calculate the Maximum Current Im a. 30.978mA b. 24.243mA c. 8.89mA d. 11.521mA
In a phase controlled full wave rectifier, the source voltage is 50 VRMS sinusoidal, the source frequency is 60 Hz and the load is 20 ohms. Since the delay angle in the circuit is 20 °, which of the following is the value of the RMS load voltage? a) 99.54 V b) 49.77 V c) 70.38 V d) 35.19 V e) 23.46 V
A de-de converter is to be built to the following specifications: Allowed de input voltage range: +3 V to +18 V Output voltage (average value): +24 V Output voltage ripple: ±0.05 V maximum at rated load Rated load: 120 W, resistive Input current ripple: ±100 mA maximum at rated load Switching frequency: 100 kHz Common ground between input and output a. Draw a circuit which can perform this function. How many switches have gates? b. What is the range of duty ratio values for each switch? c. Find circuit part (L, C, R) values which will meet the stated specifications.
i need the answer quickly
Consider the boost converter shown. Switch Q is operating at 25 kHz with a duty cycle of 0.6. Assume the diode and switch to be ideal. Under steady-state condition, the average resistance R as seen by the source is (Round off to 2 decimal places.) £2. 15 V 1 mH voor Rin k ♫ ▷ 100 uF www 102
For the buck-boost converter, determine the duty cycle, the switching frequency, and the inductor current ripple. The output voltage ripple is about 1%. vs 10 V, mH, C 0.5 micro.F, Vout=-20 V, R-IO Q
An RL load (R=0.2 Ohms, L=10 mH) is controlled by a converter. The supply voltage Vs is 600V and the chopper frequency is 200 Hz. The maximum peak to peak ripple current is equal to: Select one: a. 30A b. 55A c. 90A d. 75A
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
9- Buck type DC-DC converter, if the input voltage is 789 V and the occupancy-backlash ratio is 0.9, which of the following options is the correct load voltage. a) 710.1 etc) None c) O 7101 V d) O 78.9 V
You are tasked to look for a converter circuit design that has the specifications tabulated in Table I. The aim is to produce an output voltage of 20 V which can be used to drive a load of 120 W. The converter must operate in CCM. Table I: Design Specifications Design Parameters Input voltage Switching frequency Output current ripple Output voltage ripple Values 35 V 60 kHz 5 % 1% a) Sketch the final converter and label all parameter values b) Sketch the final operating waveforms and label all parameter values c) Determine Ve.min and Vemax- Check if the output voltage ripple matches with the design requirement.