A DC-DC step-up, Boost Converter is shown on Figure 3. Input voltage, Va = 5V, output voltage V, = 12V and R1oad= 142, L = 12µH, C = 200µF, f; = 200kHz. If the losses are negligible, determine the following: a) Does the converter operate in the continuous or discontinuous conduction mode? Explain! b) Calculate the output voltage ripple.

A DC-DC step-up, Boost Converter is shown on Figure 3. Input voltage, Va = 5V, output voltage V, = 12V and R1oad= 142, L = 12µH, C = 200µF, f; = 200kHz. If the losses are negligible, determine the following: a) Does the converter operate in the continuous or discontinuous conduction mode? Explain! b) Calculate the output voltage ripple.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current
A 60 Hz sinusoidal voltage with an RMS value of 120 V is applied to a single-phase full-wave SCR rectifier. The DC output voltage of the rectifier is 101 V, the firing angle (in degrees) of SCR is would be: O A. 36 O B. 45 O C. None of the other choices are correct O D. 30 O E. 60
find in less than 30 min
Can someone please provide a step by step solution? Thank you! The full wave rectifier in the circuit below is to deliver 0.25A and 15V (peak) to a load. The ripple is to be no larger than 0.4 V peak-to-peak. The input signal is 120 V (rms) at 60 Hz. Assume V(lambda) = 0.7 V . Determine the required turns ratio, the filter capacitance, and the diode PIV rating.
(b) Discuss the impact of connecting a large capacitor filter across the load in Figure Q1(ii). Use appropriate waveform sketch to aid your discussion. + Vp - Us R2 RL Vs ( (i) (ii) Figure Q1. Single phase half bridge rectifier: (i) with a Thyristor (ii) with a Diode
Design a bridge type full-wave rectifier fed from 220-V line through a step-down transformer (7:3). The load requires an average voltage of 17 V and average power of 9 W. Use a safety factor of 25%
For the given circuit below, it operates on a peak-to-peak input voltage of 104.6 V, F = 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. %3D Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1 D2 ... AC Input Vsec B (source) D3 D4 Load O 7.32 3.83 6.63 O 3.74 eele
a. What is the effect of applying reverse voltage on a pn junction? b. What is the critical electric field and when will it happen?
1. Build the following circuit. Use the function generator to obtain the specified AC input voltage. D4 D1 + RL 1.2K + VsN D3 Y D2 9V sin(2n 50 t) Verify the amplı, 'de and frequency of the output waveform on the load resistor, RL. Peak voltage: Waveform period: Frequency 1.d) How much power would have. en dissipated on the diodes in total, if the same output waveform was obtainea sing a full-wave rectifier with a center- tapped transformer?
5
Draw a full-wave bridge rectifier circuit (use multisim) connected to a load resistance of 470 N, with input VPP= 29 V. Connect a voltmeter across the load and an ammeter to measure the current through the load. Peak voltage of the output from the graph Average voltage across the load from the voltmeter reading Average current from the ammeter reading Insert the picture of the simulation here