You are tasked to look for a converter circuit design that has the specifications tabulated in Table I. The aim is to produce an output voltage of 20 V which can be used to drive a load of 120 W. The converter must operate in CCM. Design Parameters Input voltage Switching frequency Output current ripple Output voltage ripple Table I: Design Specifications Values 35 V 60 kHz 5 % 1 % a) Sketch the final converter and label all parameter values b) Sketch the final operating waveforms and label all parameter values c) Determine Vamin and Va,max- Check if the output voltage ripple matches with the design requirement.

You are tasked to look for a converter circuit design that has the specifications tabulated in Table I. The aim is to produce an output voltage of 20 V which can be used to drive a load of 120 W. The converter must operate in CCM. Design Parameters Input voltage Switching frequency Output current ripple Output voltage ripple Table I: Design Specifications Values 35 V 60 kHz 5 % 1 % a) Sketch the final converter and label all parameter values b) Sketch the final operating waveforms and label all parameter values c) Determine Vamin and Va,max- Check if the output voltage ripple matches with the design requirement.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Pleanswrr answrr all subparts compulsory... Either dislike...
1. For the above Boost converter, what is the duty cycle? a. 0.95 b.0.75 c. 0.25 d. None of the obove 2. For the above Boost converter, what are the average current flowing in the MOSFET and diode? a. 12A, 4A b. 12A, 12A c. 4A, 4A d. 16A, 4A 3. For the above Boost converter, what is the peak switching current flow in the MOSFET and diode? a. 19.75A, 19.75A b. 15.75A, 15.75A C. 19.75A, 15.75A d. None of this 4. what is the max voltage stress on the MOSFET and diode? a. 10V, 10V b. 10V, 40V c. 40V 40V, d. none of this 5. what is the output voltage peak to peak ripple? a. 0.3V b. 0.1V c. 0.6V d. none of the above
electronic
Note: Please do not handwritten but the diagrams should be drawn by hand.
A 3-phase half wave controlled AC to DC converter is supplied from a 250V, supply. Assume the thyristor voltage drop to be 1.6V and the load current to be continuous. Evaluate the mean output voltage when firing angle is varied at 45(degree) , 60(degree) and 90(degree)
In a full-wave bridge rectifier equivalent DC output voltage circuit, calculate the effective DC voltage output given a Vin(RMS)=110 V (60 Hz) and the turns has a ratio of 10:1. Explain each step of your calculation briefly.
I have one (1) AC source, four (4) diodes, and one (1) thyristor. In this case, I would like to obtain a full- controlled rectifier using these components; please describe the circuit?
What determines if a standard buck converter is synchronous rather than asynchronous? A. The low side switch is controllable B. The diode is fast recovery C. The inductor current ripple stays positive D. The converter can step up or down the output voltage
Derive the average and RMS output voltage for three phase half controlled rectifier with RLE Load or three phase semi converters.
Draw the circuit diagram with shape of signal after transformer, after bridge rectifier, with capacitor and with voltage regulator.
The half wave rectifier is supplied with 230V, 70HZ signal. Assume the umber of turns in the primary to secondary ratio is 7:2. Calculate the average de current through the load resistor 3KO. i) Calculate the value of input ac power, output dc power. oc-a ed States) hp
QUESTION 1 Find out the rounded integer output (in decimal format) of a10 bit A/D converter for the following two cases? Assume that the input to ADC in both cases is 500mV. Also, assume that the ADC uses a 15V supply voltage. The converter input range is 0 to 10V. Case 1: Reference voltage: 10V. Case 2: Reference Voltage: 5V. A 26 and 51 B 52 and 103 C 104 and 206 D 26 and 206 In Question 1, If a choice is given, which reference voltage you would pick? A. 5V B. 10V C. 20V D. All choices give same results In Question 1, What is the ADC output value (in decimal format) for the input of 7V for the case of reference voltage = 5V? Answer: 1023 Answers are highlighted. Work Step-by-Step solution to get the answer.