Consider the following step up converter with a resistive load of value R=5 ohms. It is supplied by a DC power source of magnitude Vs=200 V. The switching frequency is 5 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L=10 mH. The switch is supposed to be ideal. If the minimum and maximum currents in mode 1 and mode 2 are respectively 79A and 81 A, then the average supply current is: Select one: Oa. Is 80 A b. Is = 160 A Oc. Is = 81 A O d. Is = 40 A

Consider the following step up converter with a resistive load of value R=5 ohms. It is supplied by a DC power source of magnitude Vs=200 V. The switching frequency is 5 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L=10 mH. The switch is supposed to be ideal. If the minimum and maximum currents in mode 1 and mode 2 are respectively 79A and 81 A, then the average supply current is: Select one: Oa. Is 80 A b. Is = 160 A Oc. Is = 81 A O d. Is = 40 A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

find zener voltage and resistance with given values:capacitor: 470 micro Fresistor: 12 ohmV out: 12V DCI out: 1AV in: 120V AC 60 Hzdiode: 0.7V
the average values of each voltage in Figures below are: 20 V pr 10 V OV+ O 16.4v O 13.18v 16.36v 6.369v O 12.7388v O Other:
An inductive coil takes a current of 2A and consumes 160 W when connected to a 240 V AC supply. A second coil when connected across the same supply takes 3 A and 500 W. Find the total power when the two coils are connected in series to this supply.
Rc does not look like a standard resistor value? and what about choosing value for Re, it has to be standard value as well
Describe and explain the power in ac circuits; Series RLC Circuit, Parallel RLC Circuit and Power Measurement in AC Circuits
Determine the waveform of the peak output voltage at Resistor L. The winding ratio is 5:1 (gives an output of 20%).
The proper shaping of the load curve or load characteristics cannot be done by relieving the significant losses minimizing the costly generation suppressing the load at off-peak time suppressing the load at peak time
B8
The following forward converter (for questions 8-12) has the following parameters. Vin=40V, Vout=10V, Pout= 50W. The duty cycle is 40%. The primary side winding Np has 16 turns. Nr : Np: Ns Vsupply Load Vout AD: Switch S (Draw the circuit with Visio) 9. What is the turns ratio between the primary side and the secondary side winding? A. Np: Ns = 16:10 B Np:N,= 16:5 C. Np:Ns = 16:7 D. None of the above 10. Assume the auxiliary winding NT has 20 turns, what is the maximum voltage on the power switch? A. 40V В. 72V С. 80V D. None of the above 11. Still assume the auxiliary winding has 20 turns, what is the maximum voltage on the diode D1 and D2? A. 10V, 10V B. 20V, 25V C. 25V, 25V, D. 20V, 20V 12. For the above Forward converter, which of the following auxiliary winding designs will ensure fully transformer core de-magnetizing in every switching cycle? A. NT= 12 turns B. N= 30 turns C. N= 50 Turns D. All A, B, C are ok
BQ7
The following circuit has a voltage across the load of 18V, a peak-peak ripple voltage of 318mV, which would the voltage be across the load if the capacitor were damaged?
Prove that the fluctuation of voltage at the load end is largely a function of the reactive power, and the fluctuation system frequency is a function of the active power flow