The following forward converter (for questions 8-12) has the following parameters. Vin=40V, Vout=10V,Pout= 50W. The duty cycle is 40%. The primary side winding Np has 16 turns.Nr : Np: NsVsupplyLoadVoutAD:Switch S(Draw the circuit with Visio)9. What is the turns ratio between the primary side and the secondary side winding?A. Np: Ns = 16:10B Np:N,= 16:5C. Np:Ns = 16:7 D. None of the above10. Assume the auxiliary winding NT has 20 turns, what is the maximum voltage on the power switch?A. 40VВ. 72VС. 80VD. None of the above11. Still assume the auxiliary winding has 20 turns, what is the maximum voltage on the diode D1 and D2?A. 10V, 10VB. 20V, 25VC. 25V, 25V,D. 20V, 20V12. For the above Forward converter, which of the following auxiliary winding designs will ensure fullytransformer core de-magnetizing in every switching cycle?A. NT= 12 turnsB. N= 30 turnsC. N= 50 TurnsD. All A, B, C are ok

Forward converter- The forward converter is derived from the buck converter. The forward converter…

The following forward converter (for questions 8-12) has the following parameters. Vin=40V, Vout=10V, Pout= 50W. The duty cycle is 40%. The primary side winding Np has 16 turns. Nr: Np: Ns Vyuppiy D, Load Vout C D3 Switch S (Draw the circuit with Visio) 9. What is the turns ratio between the primary side and the secondary side winding? A. Np: Ns = 16:10 B Np:N,= 16:5 C. Np:N, = 16:7 D. None of the above

The following forward converter (for questions 8-12) has the following parameters. Vin=40V, Vout=10V, Pout= 50W. The duty cycle is 40%. The primary side winding Np has 16 turns. Nr: Np: Ns Vyuppiy D, Load Vout C D3 Switch S (Draw the circuit with Visio) 9. What is the turns ratio between the primary side and the secondary side winding? A. Np: Ns = 16:10 B Np:N,= 16:5 C. Np:N, = 16:7 D. None of the above

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calibri (Body) -11 by AaBbCcDx AaBbCcD AaBbC AaBbCc AaB AaBbCc. mat Painter BIU 1Normal 1No Spaci. Heading 1 Heading 2 Title Subtitle Chang Styles d Font Paragraph Styles IMPEDANCE QUIZ # 2 1. What capacitance when connected in series with a 500Q resistor will limit the current drawn from a 48-mV 465-kHz source to 20µA? * a. 144pF b. 145pF c. 146pF d. 147pF MY ANSWER: c.146pF 2. What is the total impedance at 20kHz of a series circuit consisting of a 1.5mH inductance, a 100Q resistance, and a 0.08uF capacitance? * a. 1340 41.7 b. 1930 L-37.2" C. 920 290 d. 530 2-12.6°
Input to a step up chopper is 250 v. The output required is 450 V. If the conducting time of thyristor is 200 psec, the chopping frequency is
A resistor R and a capacitor C are connected in series across a 400 V variable ac supply. When the frequency is 40 Hz, it draws 10 A current, and when the frequency is 50 Hz, it draws 15 A current. Find R and C.
Consider the following statements :A clamper circuit 1. adds or subtracts a dc voltage to a waveform 2. does not change the waveform 3. amplifies the waveform Which are correct? * O 1,2 O 1,3 O 1, 2, 3 O 2,3
When 1 A is passed through three impedance coils. A, B and C in series, the voltage drops are respectively, 6, 3 and 8 volts on direct current and 7, 5 and 10 volts on alternating current. When alternating current flows in the circuit, what is the overall power factor of the circuit?
Calculate the rms value of the output voltage of an AC-AC converter with the following specifications. Vs—110*sqrt(2)*sin(wt), Alpha Pi/6
I am getting the output of the clamper circuit wrong, how will this circuit be output ? circuit question : Set the input voltage signal to a sinusoid with 100 Hz frequency and 20V peak-to-peak amplitude with C=1μF. Obtain and plot the input and output voltage waveforms.
Due to mutual inductance between two coils, there is an induced emf in one coil due to a change in current in the other coil. O True O False O Hard to say
An inductor and a 470 ohm resistor are connected in series with a function generator. The current is 53.7mA RMS 8kHz. The reactive power is 2.32 var. Find the value of the inductance.
3. If the ratio of V/F has been kept constant and the observed value of hysteresis loss at rated frequency of 50 Hz is 18 W, the measured value of core losses is 35 W, Find the total core losses at the frequency of 60 Hz. 02:
A transformer is connected to a primary impedance of 2kQ and a secondary impedance of 100O. The primary current is 500mA RMS. Calculate the magnitude of the secondary current. O 258mA O 1.51A O 2.24A O 500mA
What is the relationship between R, L, and C components in a series AC circuit?