A beam is supported as shown below:The beam is to carry the following loads, in (kN)and in (kN/m), in the table below:Determine the following:3. Maximum moment reaction at A, MA in kN-m A beam is supported as shown below:HingeCED1 m1 m1 m1m1 mThe beam is to carry the following loads, in (kN)and in (kN/m), in the table below:LOADW(DL) W(LL) P(LL)SET 1 (1,2,3,4,5)SET 2 (6,7,8,9,0)202540301550Determine the following:3. Maximum moment reaction at A, MA in kN-

##Calculation of REACTION AND BENDING MOMENT MAXIMUM ###

Answered: A beam is supported as shown below: The…

A beam is supported as shown below: The beam is to carry the following loads, in (kN) and in (kN/m), in the table below: Determine the following: 3. Maximum moment reaction at A, MA in kN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

H.W3: Analysis the structure shown in figure, El is constant W=20 KN/m P =40 KN B C 4m 3 3
2
Determine all the support reaction of the given figure A W (KN/m) L b B
A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 8 mm and a length of L₁ = 2.7 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 25 mm and a length of L₂ = 1.4 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 64 kN is applied to the rigid bar. L₁ (1) Answer: 01 i 02= i L2 (2) (1) MPa MPa
Consider the frame as shown in figure. Assume A is a pin jointed support and C is a roller jointed support. The maximum bending moment occurs at a point R, the distance of R from A measured vertically from A is 40 kN/m 4 m 80 kN 2 m 2m 3 m
A steel strip is clamped at left end and supported by a spring at right end. The spring has a stiffness of k = 3 N/mm. The strip is 5 mm wide and 10 mm high. Take E = 200 GPa. A 10 mm -200 mm What is the reaction of the spring (N) 50 N B k:
A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 11 mm and a length of L1 = 1.5 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 21 mm and a length of L2 = 0.8 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 76 kN is applied to the rigid bar.
Already answered in Bartleby. Do not copy the solutions. Please double check the solutions! Statics of Rigid Bodies (Round off to two (2) decimal places. Include negative sign (-) if the answer is negative.) 1. The line of action of the 3000 lb force runs through te points A and B as shown in the figure. Determine: x scalar component of F
3)
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15,000 ksi] rods, and a solid steel [E = 30,000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.500 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.360 in. If all bars are unstressed before the load P is applied, determine the normal force in steel rod (2) after a load of P = 36 kips is applied.
In the beam depicted above, ?A is a fixed support. The magnitude of ?=365?/?W=365N/m, ?=60?P=60N and all lengths denoted by ?=1.5?a=1.5m. The system is in equilibrium. Using the given sign convention, answer the following questions. a) Calculate the vertical component of the external reaction at ?A in ???????Newtons. b) Calculate the horizontal component of the external reaction at ?A in ???????Newtons. c) Calculate the moment component of the external reaction at ?A in ??????Newton ??????metres. d) Calculate the shear force at point ?B in ???????Newtons. e) Calculate the bending moment at ?B in ??????Newton ??????metres. f) Calculate the shear force at point ?D in ???????Newtons. g) Calculate the bending moment (absolute value) at ?D in ??????Newton ??????metres. h) Calculate the shear force at point ?E in ???????Newtons. i) Calculate the bending moment at ?E in ??????Newton ??????metres. j) Calculate the shear force at point ?H in…
RIGID BODY TRANSLATION SHOW FREE BODY DIAGRAMCOMPLETE AND CLEAR SOLUTION DON'T ROUND OFF DETERMINE THE REACTIONS AT B, C, AND D Note: Pin supports can resist both vertical and horizontal forces.