2. Refer to Figure Q2, which shows a diagram of a loaded frame. Using the Principle of Virtual Work, calculate the following: a. The moment reaction at the clamped end. b. The internal bending moment, at the point where the 5 kN load is applied. 3 kNm 0.5 m 5 kN 0.25 m 0.5 m Figure Q2 - A loaded frame.

2. Refer to Figure Q2, which shows a diagram of a loaded frame. Using the Principle of Virtual Work, calculate the following: a. The moment reaction at the clamped end. b. The internal bending moment, at the point where the 5 kN load is applied. 3 kNm 0.5 m 5 kN 0.25 m 0.5 m Figure Q2 - A loaded frame.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Statics. A similar question is provided but I still don't get it. Please show fbd as the solved example
3)
A solid 0.66-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 Ib-ft 50 lb-ft 70 Ib-ft 30 lb-ft 1594psi 2126psi 1981psi 1786psi 2936psi
A1
Determine the reaction at the support of the beam/frea, shown in the figure using the Force Method Analysis. Draw the shear and bending moment diagram
6
Question 4(a) The uniform bar shown in Figure 4 weighs 428 N. It is supported by a pin at A and a cable that runs around the pulley, D. It is subjected to a uniformly distributed load of 17.7 N/m and 12.5 Nm clockwise moment at E. Beam is in equilibrium position as shown in the Figure. Take a = 0.41 m and b = 2.5 m. Determine the tension in the cable and the reaction force at A, both in Newtons. w N/m 75° A ▼▼ ▼ ▼ 12.5 Nm B E 1 m 0.5 m m b Figure 4 Question 4(b) Find a truss from your neighborhood where you can take a photo safely. It does not have to be taken from the perfect angle and as long as we can see the complete truss that is good enough. One photo would be ideal but upto 3 photos can be used. Include these photos in your solutions for this question and based on these photos draw this 2D truss (exact dimensions are not required) with the supports too. Comment on the possible loads and their locations that may be applied to the truss. Discuss the assumptions that you have to…
The jib crane is designed for a maximum capacity of 9 KN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.3 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 0.8 m? (b) What is the value of R when x = 3.5 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 9 KN 1.6 m Questions: (a) If x= 0.8 m, R = KN (b) If x= 3.5 m, R= i KN m (c) The minimum value for R = i (d) The pin should be designed to hold -2.9 m i kN at x = kN. i
The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 190 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.8 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 1.6 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 39° x m 6 KN -2.5 m 1.5 m Questions: (a) If x= 1.6 m, R= (b) If x= 3.3 m, R = i (c) The minimum value for R = i (d) The pin should be designed to hold i KN KN kN at x = kN. i
Question 5 T/2 В 1200 Nm A homogeneous steel shaft (G=83GPA) is loaded as shown in the above Figure. Assuming T = 300 N-m, determine the torsional force in N-m in Member BC. Note: Include sign (+/-), assuming the direction of Torsion (T) at D is positive Given: AB: Length = 1.75m, Diameter = 75mm BC: Length = 1.50m, Diameter = 60mm AB: Length = 1.00m, Diameter = 40mm
The torques shown are exerted on pulleys A and B which are attached to solid circular shafts AB and BC. In order to reduce to total mass of the assembly, detemine the smallest diameter of shaft BC for which the largest shearing stress in the assembly is not increased. TA = 300 N m 30 min B TH = 400 N- m 46 nn
Q.2) (a) Calculate the support reactions of the loaded beam shown below. (b) Write equations for w(x), V(x) and M(x) of the beam using singularity functions. (c) Sketch the shear-force and bending moment diagrams for the beam for the beam using the Graphical method. Label the values of shear-force and bending-moment at all key points. 350 N.m G 0.5 m4 2m 95 N/m, 200 N 250 N.m 80 N/m 2m 300 N 0.5 m