Force P = 375 N is applied at A as shown. Find the moment about point D. Enter a positive answer if the moment is counterclockwise and a negative answer if the moment is clockwise. Note that the lengths are given in mm but the answer is asked for in N m. 100 mm- -200 mm- 200 mm 25° MD Nm D 125 mm C B

Q: The bear cross section shown below has been proposed for a short pedestrian bridge. The cross…

A: Determonation of shear stress at H

Q: Determire the reactiors of the given beam using morment distribution method. w = 25 kN/m, P: = 25…

A:

Q: The sign has a mass of 100 kg with center of mass at G. Determine the x, y, z components of reaction…

A: mass of sign = 100 kg  center of mass at G

Q: The simple machine shown below has 2 parts connected via a pin at A. The gripp ceeth at B exerts a…

A:

Q: Analyze the given frame. P units in kN/m P 3m P 5m 4m pin 0.7P 4m

A:

Q: y | 1 A -X 25' 15⁰ 40° C F = 13 kips 15' B 11 .n

A:

Q: F 200 N F3=300N M. 100 Nm 0.4 m F, 300N 0.5 m 0.6 m The pipe system shown in the figure is supported…

A:

Q: The simply supported beam is subjected to the force F-550 N and the uniform distributed load with…

A:

Q: Problem 4 The shown bent tube is connected to a guide at A and rests on a roller support at B. It is…

A:

Q: There is a beam as shown in the figure below, and the flexural stiffness of the beam section is…

A:

Q: Question The electric motor exerts 600 Nm torque on the aluminum shaft ABCD when it is rotating at a…

A: T = 600 Nm GBC = 16 GPa or 16000 MPa GCD = 12 GPa or 12000 MPa dBC = 30 mm

Q: The curved rod lies in the x-y plane and has a radius of 3 m. If a force of F = 80 N acts at its end…

A: Given Data : F= 80 N Radius = 3m Determine the moment of that force = 80 N about point O?

Q: 160 mm 480 N 60 mm 80 mm CD = Cx = -795N, left E 150 mm 60 mm 100 mm B.

A:

Q: A В D 400 mm, 625 mm 1. The aluminum rod, AB (G = 27 GPa), is bonded to a brass rod BD (G = 39 GPa)…

A: Given:- The modulus of rigidity of aluminum rod AB = 27 GPa The modulus of rigidity of brass rod BD…

Q: Problem 6: For the beam and loading shown below, derive an expression for the reaction force at B.…

A: Given :

Q: Determine the forces in members AB, AC, and AD. Forces are positive if in tension, negative if in…

A: Given Data: The applied force at point A is P=4.9 kN.   To Determine: The forces in members AB, AC…

Q: Consider the beam shown in (Figure 1). EI is constant. Assume (2) and (3 are rollers. Take F = 46 kN…

A:

Q: Determine the equation of the elastic curve. EI is constant.

A: Consider the free body diagram of the beam shown below. Consider the moment equilibrium about point…

Q: Problem 5.2: The structural steel wide-flange beam shown in Figure (5.24) is a W10x60 section (See…

A: Allowable flexural stress = 28 ksi  Determine  a. Maximum moment about z-axis.  b. Maximum moment…

Q: One of the cranks of a child's bicycle is shown. The entire crank lies in the xy plane. Take F= 90…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.