A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solidbronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 17 mm and a length of L1 = 2.7 m. They are symmetricallypositioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 25 mm and a length of L2 = 1.5 m. If allbars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 60kN is applied to the rigid bar.L1(1)PL2Answer:01 =MPа02 =iMPа(2)

Answered: Image /qna-images/answer/7a9cf0c9-7bbf-4f10-ae79-624353d1a137.jpg

Answered: determine the normal stresses in the…

Engineering

Civil Engineering

determine the normal stresses in the aluminum and bronze rodsa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Don't copy & correct solution
Problem 3: Inside a steel tube, 2.4 meters long, 34 mm radius, and 1.5 mm thick, 32.5A circular bar made of aluminum with a radius of mm is inserted and these two materials arethey are linked together to form a cross section that will work. This cantilever beam obtained from end Ait is fixedly supported. This cantilever beam,A torque of T = 900 Nm from end B(torque) is applied. Stiffness modulus of steel, Strength= 77 GPa and the stiffness modulus of aluminum Gal = 26Since GPa is the rotation at point BWhat is the (torsion) angle? Calculate.
Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod (1) has an elastic modulus of E1 = 15,000 ksi and a diameter of d1 = 0.60 in. Aluminum rod (2) has an elastic modulus of E2 = 10,000 ksi and a diameter of d2 = 0.70in. Aluminum rod (3) has a diameter of d3 = 1.00in. The yield strength of the bronze is 48 ksi and the yield strength of the aluminum is 40 ksi. Assume a = 2.5 ft, b = 1.5 ft, L1 = 6 ft, L2 = 8 ft, and L3 = 3 ft.(a) Determine the magnitude of load P that can safely be applied to the structure if a minimum factor of safety of 2.2 is required.(b) Determine the deflection of point D for the load determined in part (a).(c) The pin used at B has an ultimate shear strength of 50 ksi. If a factor of safety of 3.4 is required for this double shear pin connection, determine the minimum pin diameter that can be used at B.
A 260 mm bar AB with a rectangular cross section of 17 x 30 mm, consists of two aluminium layers with cach being 6 mm thick and brazed to a centre steel layer of 5 mm thickness as shown in Figure Q3. An axial tensile force of P- 37 kN is applied to the assembly by means of a rigid end cap at B. Given that the assembly is fixed at end A and the Young's modulus of aluminium and steel are E.= 70 GPa, Es= 200 GPa, respectively, determine: i Whether this structural configuration is statically determinate or statically indeterminate, and clearly explain your reasoning. ii. The normal forces in the aluminium layers and the steel layer i. The normal stress in the aluminium layers and the steel layer. State whether the stresses are in tension or compression iv. Determine the deformation of the assembly Cross section of the bar 6 mm 5 mm 6 mm 30 mm 260 mun Aluminium. Steel- Aluminitum Nא 37 30 mm
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E, = 10000 ksi] alloy. The length of segment (1) is L, = 70 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 98 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of 8z = 2100 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 Aluminum B Сорer Answer: in. AL = i
A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an aluminum alloy (E = 10,000 ksi) pipe B as shown. The supports at the top of the rod and the bottom of the pipe are rigid, and the materials were unstressed before the load was applied. The cross-sectional areas of rods A and pipe B are 0.80 in2 and 3.00 in2 respectively. Determine The normal stress in rod A in ksi, The normal stress in pipe B in ksi and The displacement of plate C in inches. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 5 decimal places.
TWO SOLID CYLINDRICAL RODS ARE JOINED AT B AND LOADED AS SHOWN. ROD AB IS MADE OF STEEL (E = 210 GPa) AND ROD BC OF BRASS (E = 108 GPa). DETERMINE (A) THE TOTAL DEFORMATION OF THE COMPOSITE ROD ABC, (B) THE DEFLECTION OF POINT B. 40 KN 400 mm 600 mm A B C 30 mm 50 KN 50 mm
Problem 1 A rigid bar AC is loaded and supported as shown. Bar AB and CD are unstressed before the load is applied. Bar AB is made of steel (E = 30000ksi) and has a cross-sectional area of 1.25 in?. Bar CD is made of brass (E = 15000ksi) and has a cross-sectional area of 0.75 in². Determine: %3D 12 k/ft (1) The stresses in bars AB and CD (2) The vertical displacement (deflection) of C relative to the displacement at point (Note: express your answer in inches and include a direction) TI!||! 3 ft 4.5 ft
Compound axial member ABC has a uniform diameter of d = 1.50 in. Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 80 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 112 in. When axial force P is applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 1700 pin./in. in longitudinal direction. What is the total elongation of member ABC? L2 (1) d Aluminum В (2) Сopper
The uniform beam of weight W is to be supported by the two rods, the lower ends of which were initially at the same level. Determine the ratio of the areas of the rods so that the beam will be horizontal after it is attached to the rods. Neglect the deformation of the beam. Steel 3 m E = 200 GPa Aluminum 2 m E = 70 GPa W 1.5 m -3 m- + 0.5 m
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1260 μm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. 1413 μm/m 1223 μm/m 1286 μm/m 738 μm/m 1553 μm/m
5. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stresses of 150 MPa in the steel rod and 70 MPa in the bronze rod? -2 m- -1.5 m- 1.5 m- Bronze A = 300 mm2 E = 83 GPa L=2 m Steel A = 900 mm2 E = 200 GPa L = 1.5 m