A beam fabricated from western white pine has been reinforced by bonding steel strips on its top and bottom surfaces as shown. If the design is limited to Owood = 1 ksi in the wood and steel = 34.4 ksi in the steel, determine the maximum bending moment if the beam bends about its horizontal axis of symmetry. Given: ● ● ● L₁ = 11.2 in L₂= 1.7 in L3= 4.3 in Mmar - L2 STEEL 201 N.A. -- L₁ WOOD number (rtol=0.01, atol=1e-05) kip- in L2

A beam fabricated from western white pine has been reinforced by bonding steel strips on its top and bottom surfaces as shown. If the design is limited to Owood = 1 ksi in the wood and steel = 34.4 ksi in the steel, determine the maximum bending moment if the beam bends about its horizontal axis of symmetry. Given: ● ● ● L₁ = 11.2 in L₂= 1.7 in L3= 4.3 in Mmar - L2 STEEL 201 N.A. -- L₁ WOOD number (rtol=0.01, atol=1e-05) kip- in L2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Anil
If F1= 24kN F2=26kN F3=21.5kN Calculate the second area of moment of the beam using the dimensions in the attached image
If Mz = 715 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section, assume a = 10 in. b = 14 in. d = 39 in. r = 5 in. The centroid of the cross section is located 17.9 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 60436 in.4.
The cross section of a wood beam carries a bending moment M of magnitude 20R lb.-in. acting at 100 to the horizontal. Determine(a)the angle between the neutral axis and the horizontal; and (b) the maximum bending stress acting on the cross section. Note R=993
The box beam shown in Figure 1 is subjected to an internal moment of M= 4 kN.m which is directed as shown. Determine the maximum bending stress developed in the beam and the orientation of the neutral axis. 50 mm 25 mm 50 mm @ 25 mm 50 mm 50 mm 45° STO M 150 mm 150 mm
A beam fabricated from western white pine has been reinforced by bonding steel strips on its top and bottom 1.5 ksi in the surfaces as shown. If the design is limited to wood = 1.5 ksi in the wood and a steel wood and steel = 35.6 ksi in the steel, determine the maximum bending moment if the beam bends about its vertical axis of symmetry. L3 Given: • L₁= 10 in • L₂ L₂ = 0.9 in • L3= 5.3 in Mmar SEHERAPECES SANTREMANEN La prender PERANAN PE P number (rtol-0.01, atol=1e-05) STEEL E WOOD N.A. L₁ kip. in L₂ L₂ Phu
I want the correct answers please
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a -5 m, b = 3 m, Pg - 55 kN, Pc-75 kN, and PE - 25 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a Ay= 41.54 Answers: a B (a) V- i (b) V= (c) V= i (d) V- i i a Calculate the reaction forces A, and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) B C a b C Pc b D Dy D kN, Dy= 113.46 kN. a Determine the shear force acting at each of the following locations: (a) x = 2.5 m (b) x-7.5 m (c) x = 11.5 m (d) x = 15.5 m kN. When entering your answers, use the shear force sign convention. kN. a kN. E E x kN.
The rod is supported by smooth journal bearings at A and B that only exert vertical reactions on the shaft. Part A Determine its smallest diameter d if the allowable bending stress is oallow = 130 MPa (Figure 1) Express your answer with the appropriate units. HA ? d = Value Units Figure < 1 of 1 Submit Request Answer 12 kN/m Provide Feedback 3 m 1.5 m
. A composite beam, made of aluminum (Al) and magnesium (Mg), has the cross section shown below. The moduli of elasticity for aluminum and magnesium are EAI = 70 GPa and EMg = 45 GPa, respectively. If the allowable flexural stresses (in tension and com- pression) are All 135 MPa for the aluminum and Mg 120 MPa for the magnesium, determine the maximum allowable bending moment for the beam. all - 0.2 m 0.2 m Al 0.2 m Mg C
Hi, I want to find the location on the beam where the maximum bending moment happens as measured from point A. I have already gathered the following information. FAx= 0 FAy= 25.0869 FCy= 32.913 the sheer force at B= 3.087 The bending moment at B = 77.4785 Let the loading coefficents be: W1 = 4 kN/m, W2 = 8 kN/m Let the lengths be: L1 = 5.5m , L2 = 6m. If anyone could help me with this last step of the problem that would be great.
Answer the following: