M= 2. A beam of length 10 m and of uniform rectangular section is supported at its ends and carries uniformly distributed load over the entire length. Calculate the depth of the section if the maximum permissible bending stress is 16 N/mm² and central deflection is not to exceed 10 mm. Take the value of E = 1.2 x 104 N/mm². Use the following g equations: w.L² W.L 8 8 W.L 8 Yc= = 161 d 5 384 X WL³ EI W = w.L)

M= 2. A beam of length 10 m and of uniform rectangular section is supported at its ends and carries uniformly distributed load over the entire length. Calculate the depth of the section if the maximum permissible bending stress is 16 N/mm² and central deflection is not to exceed 10 mm. Take the value of E = 1.2 x 104 N/mm². Use the following g equations: w.L² W.L 8 8 W.L 8 Yc= = 161 d 5 384 X WL³ EI W = w.L)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Parvinbhai
Determine the bending stress in a 5-meter simple beam with a concentrated load of 1 kN at midspan. The beam has a rectangular section with b = 2 in and h = 4 in.
A simply supported beam of hollow rectangular cross section is 100mm deep and 60mm wide with a wall thickness of 10mm. The beam has a span of 6m and carries a load as shown . Neglecting the weight of the beam draw a bending moment diagram and calculate the maximum bending moment. And determine the maximum bending stress in the material.
A uniform distributed load of 4 kN/m is applied to a cantilever beam as shown. What is the resisting bending moment equation for any section of the beam? 4 kN/m Select one: O a. M, = -2x³ kNm O b. Mr = -2x² kNm O c. M₁ = -4x² kNm O d. Mr = -8x kNm O e. None of these options Ai →X 2M
Question 1
If Mz = 200 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section, assume a = 7 in. b = 10 in. d = 26 in. r = 3.5 in. The centroid of the cross section is located 11.96 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 12903 in.4.
6 kN/m Since the bending safety stress *em = 10 MPa, shear safety stress h em = 600 kPa of the rectangular section beam given in the figure В and whose width is b = 150 mm, the height of the beam section h is at least how much is the height of the beam section in order not to exceed the safety stress values. should be. -b -3 m 2 m
The cross-sectional dimensions of a beam are shown. Assume b=3 in., tetw=0.4375 in. and d=3.375 in. (a) If the bending stress at point K is 1860 psi (T), determine the internal bending moment M, acting about the z centroidal axis of the beam. (b) Determine the bending stress oH at point H (positive if tension, negative if compression). K d H bf Answers: (a) M2 = i Ib-ft. ( b) σμ i psi. %3D Save for Later Attempts: 0 of 1 used Submit Answer
A simply supported wood beam with a span of L = 11 ft supports a uniformly distributed load of w = 840 lb/ft. The allowable bending stress of the wood is 1400 psi. If the aspect ratio of the solid rectangular wood beam is specified as h/b = 1.5, determine the minimum width b that can be used for the beam. O 5.54 in. O 7.03 in. O 6.62 in. O 8.58 in. O 4.15 in. L h
Calculate the internal shear force and the internal bending moment for the beam at every point x, and sketch the shear and moment diagrams. At what point in the beam (x=?) does the maximum normal stress occur? Find the maximum normal stress, 0 , due to bending, At what point in the cross section (y=?) does the maximum normal tensile stress occur?? Find the magnitude of the maximum transverse shear stress on the cross section, T, due to bending at the point “A”. At what point in the cross section (y=?) does the maximum transverse shear stress occur?