A simply supported beam of hollow rectangular cross section is 100mm deep and 60mm wide with a wall thickness of 10mm. The beam has a span of 6m and carries a load as shown . Neglecting the weight of the beam draw a bending moment diagram and calculate the maximum bending moment. And determine the maximum bending stress in the material.

Q: Draw the SFD and BMD for the beams loaded as shown in  Calculate the position and magnitude of ma

A: Given:

Q: Calculate the shear force and bending moment for the simply supported beam of length 8m with the…

A:

Q: Find the maximum bending stress in the rectangular wooden beam,  if the maximum moment is 28 kNm and…

A: Answer: The maximum bending stress in the rectangular wooden beam is 5 MPa.

Q: When loads and moments are applied to the cantilever beam as shown in the picture below, draw the…

A:

Q: Q.2: The simply supported beam in Fig .below has a rectangular cross section mm wide and 200 mm…

A: Given data is

Q: An 8-meter propped beam(fixed at the left) is loaded with 100 kN-m counterclockwise moment at the…

A:

Q: A vertical loads of 400 N acts at the end of a horizontal rectangular cantilever beam 2 m long and…

A:

Q: **** A wood beam carries a bending moment of 15 500 lb-in. It has a rectangular cross- section of…

A:

Q: For the beam and loading shown, draw the shear and bending moment diagrams. Note: Support A is…

A:

Q: 10 in 5) Find the centroid ( â, ŷ ) and Ix for the shape shown. Use a large rectangle and a small…

A: Solution: Let large rectangle area  A1=10×15.5=155in2 Let small rectangle area A2=6.5×6=39in2 We…

Q: A simply supported beam of width 100 mm, height 200 mm and length 4 m is carrying a uniformly…

A:

Q: (a) derive equations for the shear force V and the bending moment M for any location in the beam.…

A:

Q: A cantilever beammade up of a material with the density of 2000kg/m3 has a circular cross section…

A:

Q: A beam with the cross-section shown is carrying a bending moment of M. Calculate the maximum bending…

A:

Q: A cantilever beam of cross-section 90 mm. width 120 mm deep carries a UDL of 12 KN/m. over the…

A: When a cantilever beam having length 'L' is subjected to a UDL having intensity ω kN/m then maximum…

Q: A built up wooden beam is made up of two 50 mm by 150 mm sections glued on the lower sides of a 100…

A: To Find :  The maximum bending stress . Given : The built-up beam is made up of cross-sections: b1 ×…

Q: A simply supported beam of length 5m, carries a uniformly distributed load of 12019080kN/m extending…

A:

Q: 2000 Ib 300 lb/ft 6 in, TI A 4 in. -3 ft- 3 ft-

A: Calculate the reaction at the support, Total load on beam is=300×6+2000…

Q: Select the lightest-weight wide-flange beam from Appendix B that will safely support the loading.…

A:

Q: Draw shear and bending moment diagrams for the beamin Figure 3.14b, which carries a uniformly…

A: givencantilever beam as shown below

Q: Draw the fi aximum b

A: GIVEN:length of beam l=4mload at free end =4kN

Q: 10. A 30m long horizontal beam carries a uniformly distributed load of 1 kN/ m on the whole length…

A: To determine:Position of second the support for minimum bending moment.SFD and BMD

Q: A rectangular beam 80 mm x 40 mm is 3m long and simply supported at the ends. It carries a load of 1…

A: To find: The maximum bending stress. Given: The width of the beam is b=80 mm1 m1000 mm=0.08 m. The…

Q: A gantry crane of weight W-100 Kg moves across a bridge with the length 1-5 m. The front axle of the…

A:

Q: Please solve it and show your work.

A:

Q: .A steel simply supported beam 16 ft and 8 inches in length is subjected to a concentrated load of…

A:

Q: A simply supported 3 m long beam with a point load of 5 kN and a cross section of 50 mm * 80 mm is…

A:

Q: A horizontal beam under bending has a maximum bending stress of 100 MpA

A:

Q: Calculate the modulus of section of rectangle beam of breadth 120 mm and height 200 mm

A: Bending equation is given as: σy=MIσ=MyIσ=MZ Here, Z is the section modulus. Thus, section modulus…

Q: The beam shown below is subjected to a point load of 10kN and a uniformly distributed load of 3kN/m,…

A:

Q: Please answer and show your work.

A: Approach to solving the question: Detailed explanation: Examples: Key references:

Q: A beam of uniform section 10 m long carries a udl of 2KN/m for the entire length and a concentrated…

A: Draw the free-body diagram of the beam.     Apply force equilibrium in a vertical direction.…

Q: Draw the shear and moment diagram of the cantilever beam shown below. For this part, please show the…

A: Consider upward force & CW moment as (+)ve and downward force & CCW moment as (-)ve. Let…

Q: Maximum bending stress increases with the decrease in height for a rectangular cross-section beam.…

A: GIVEN DATA STATEMENT GIVEN - Maximum bending stress increases with the decrease in height for a…

Q: 个 3.2. kN/m 2 im Ar A IT 3m 2m 1.9 kN.m

A: The support at B is roller support

Q: Calculate the bending moment at points A and B for the beam shown below.

A:

Q: Derive the formula for the bending stress of a beam with a rectangular cross section and triangular…

A: Derive the formula for the bending stress of a beam with a rectangular cross section and triangular…

Q: 1. A bending moment of 5800 lb-in. is applied to a beam having a rectangular cross- section with…

A:

Q: Plot the shear and moment diagrams for the beam loaded with both the distributed and point loads.…

A:

Q: The compound beam shown in (Figure 1) is subjected to a uniform dead load of 300 lb/ft and a single…

A:

Q: The beam shown has an second moment of area of 9,500,000 mm and a controlling section modulus of…

A: Maximum flexural stress due to bending is given by the following realation, Sigma,b=Mmax*Ymax/INA…

Q: A 6-m simply supported beam AB supports a trapezoidal distributed load. The intensity of the load…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.