A batch of 10 cutting tools could produce 500 components while working at 50 rpm with a tool feed of 0.25 mm/rev and depth of cut of 1 mm. A similar batch of 10 tools of the same specification could produce 122 components while working at 80 rpm with a feed of 0.25 mm/rev and 1 mm depth of cut. How many components can be produced with one cutting tool at 60 rpm?

A batch of 10 cutting tools could produce 500 components while working at 50 rpm with a tool feed of 0.25 mm/rev and depth of cut of 1 mm. A similar batch of 10 tools of the same specification could produce 122 components while working at 80 rpm with a feed of 0.25 mm/rev and 1 mm depth of cut. How many components can be produced with one cutting tool at 60 rpm?

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.3: Machining Operations On The Lathe

Problem 5RQ: Calculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a...

See similar textbooks

Related questions

Q: a production turning operation, the workpart is 60 mm in diameter and 500 mm long. A feed of 0.75…

Q: A turning operation is performed using a rake angle of 15degree. Cutting conditions are, feed= 0.30…

Q: A two-spindle drill cuts two holes at the same time, one 1/2 inch and one 3/4 inch. The workpiece is…

Q: Face milling, using an Ø 75 mm cutter with 10 inserts rotating at 280 rpm, is being carried out on a…

A: given; diameter of cutter (D)=75mmnumber of inserts (n)=10rotating speed (N)=280rpmlength of…

Q: 8. Why do we need to set the proper tool orientation in the register before attempting to use cutter…

A: this question is about the topic of machining in production engineering. The importance of the tool…

Q: TRUE OR FALSE. IF FALSE WHAT WORD MAKES THE STATEMENT INCORRECT AND WHAT IS THE CORRESPONDING…

A: When the machining of a object is done by the cutting tool then in that case the chip is formed.…

Q: A shaft shown in Figure Q3 is to be machined using a lathe machine. The diameter of a raw block is…

A: Explanation: The stepwise procedure to solve this problem is shown in the following attached image:

Q: Using slot milling with a cutting tool surface width of 36mm was performed from the top surface to…

A: Given:The width of the cutting tool surface, The dimensions of the workpiece is The diameter of the…

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.

Question

A batch of 10 cutting tools could produce 500
components while working at 50 rpm with a tool
feed of 0.25 mm/rev and depth of cut of 1 mm.
A similar batch of 10 tools of the same
specification could produce 122 components while
working at 80 rpm with a feed of 0.25 mm/rev and
1 mm depth of cut. How many components can
be produced with one cutting tool at 60 rpm?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please answer all parts
Solve First one Only
A NC lathe cuts two passes across a cylindrical workpiece under automatic cycle. The operator loads and unloads the machine. The starting diameter of the work is 3.00 in and its length = 10 in. The work cycle consists of the following steps (with element times given in parentheses where applicable): 1 - Operator loads part into machine, starts cycle (1.00 min); 2 - NC lathe positions tool for first pass (0.10 min); 3 - NC lathe turns first pass (time depends on cutting speed); 4 - NC lathe repositions tool for second pass (0.4 min); 5 - NC lathe turns second pass (time depends on cutting speed); and 6 - Operator unloads part and places in tote pan (1.00 min). In addition, the cutting tool must be periodically changed. This tool change time takes 1.00 min. The feed rate = 0.007 in/rev and the depth of cut for each pass = 0.100 in. The cost of the operator and machine = $39/hr and the tool cost = $2.00/cutting edge. The applicable Taylor tool life equation has parameters: n = 0.26 and…
A two-spindle drill cuts two holes at the same time, one 1/2 inch and one 3/4 inch. The workpiece is 1.0 inches thick. Both drills have point angles of 118 degrees and the cutting speed for the material is 300 ft/min. The rotational speed of each drill can be set individually but the feed rate for both holes must be set to the same value because they move together into the material. The feed rate is set so that the total metal removal rate of both drills combined does not exceed 1.50 in3/min. Determine (a) maximum feed rate (in/min) that can be used, (b) individual feeds (in/rev) for each hole, and (c) cutting time for the operation.
Expert Q&A Done The top surface of a rectangular workpart is machined using a peripheral milling operation. The workpart is 735 mm long by 50 mm wide by 95 mm thick. The milling cutter, which is 60 mm in diameter and has five teeth, overhangs the width of the part equally on both sides. Cutting speed = 80 m/min, chip load = 0.30 mm/tooth, and depth of cut = 7.5 mm. (a) Determine the time required to make one pass across the surface, given that the setup and machine settings provide an approach distance of 5 mm before actual cutting begins and an overtravel distance of 25 mm after 1.2 9. 20 65 73 actual cutting has finished v in seconds. (b) What is the maximum material 3.9 239 removal rate during the cut v in mm3/sec? 0.127 5
Turning Operation In a production turning operation, the foreman has decreed that a single pass must be completed on the cylindrical workpiece in 4.8 min. The piece is 400 mm long and 150 mm in diameter. Using a feed = 0.43 mm/rev and a depth of cut = 4.0 mm, what cutting speed must be used to meet this machining time requirement? Hint: Re-arrange the Tm equation to find v in m/min Tm= T.DO.L v.f 1.522
In a production turning operation, the workpart is 60 mm in diameter and 500 mm long. A feed of 0.75 mm/rev is used in the operation. If cutting speed=9 m/s, the tool must be changed every 4 workparts; But if cutting speed=5 m/s, the tool can be used to produce 50 pieces between tool changes. Determine the Taylor tool life equation for this job. (use the equations given below for solution)
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes
A HSS tool is used to turn a steel workpart that is 300 mm long and 80 mm in diameter. The parameters in the Taylor equation are: n = 0.13 and C = 75 (m/min) for a feed of 0.4 mm/rev. The operator and machine tool rate = $30.00/hr, and the tooling cost per cutting edge = $4.00. It takes 2.0 min to load and unload the workpart and 3.50 min to change tools. Determine: Tutting speed for maximum production rate, Tool life in min of cutting, and Cycle time and cost per unit of product. determine cutting speed for minimum cost.
Write the NC part program for the part. Holes are threaded and requires two tools; T1 is a 0.5" HSS drill bit and T2 is a 0.5" tapping bit. The rest of the features are cut using a 0.75" HSS milling tool, T3. Feed rate and spindle speed are 10 ipm and 2000 rpm. The material is low- carbon steel. Part thickness is 0.5”. Use dotted lines two show the path of tools movements. Set up proper operation conditions as discussed in the class today.
An end milling operation is carried out along a straight line path that is 325 mm long. The cut is in a direction parallel to the x‑axis on a CNC machining center. Cutting speed = 30 m/min, and chip load = 0.06 mm. The end milling cutter has two teeth and its diameter = 16.0 mm. The x‑axis uses a DC servomotor connected directly to a leadscrew whose pitch = 6.0 mm. The optical encoder emits 400 pulses per revolution of the screw. Determine (a) feed rate during the cut, (b) rotational speed of the motor, and (c) pulse rate of the encoder at the feed rate indicated.
Want neat and clean solutions