A Barangay power station supplies 60KW to a load over 2500 ft, 100mm squared, two conductor copper feeders, the resistance of which is 0.078 ohm per 1000ft. The bus bar voltage is maintained constant at 600V. Determine the maximum power which can be transmitted.

A Barangay power station supplies 60KW to a load over 2500 ft, 100mm squared, two conductor copper feeders, the resistance of which is 0.078 ohm per 1000ft. The bus bar voltage is maintained constant at 600V. Determine the maximum power which can be transmitted.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An earth “ground” at the base of the transmission line tower has a resistance of 2W. If a lightning stroke of 20kA strikes the tower, what would be the power dissipated in the “ground”? What would be the voltage drop across the “ground”?
ii) A string of suspension insulators consists of three units if the voltage across the line unit is 20 kV. The ratio of self-capacitance to shunt capacitance of each unit is 6:1. Determine a) V1 Answer for part 1 b) V2 Answer for part 2 c) VPh Answer for part 3 d) %String Efficiency Answer for part 4
Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and have the following characteristics: Area 1: R1 = 0.01 pu and D1 = 0.8 pu on a base of 1200 MVA Area 2: R2 = 0.02 pu and D2 = 1 pu on a base of 600 MVA The power flow direction on the tie line is from Area 1 to Area 2. Using a common base of 1000 MVA, what is the change in prime mover power (in MW) in Area 2 (APmech2) for a load increase of 125 MW in Area 1? Select one: O a. 51.67 MW O b. None of these c. 24.74 MW O d.204.24 MW
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 425 MVA rating, R1 = 0.015 pu (on the 425 MVA base), initial output P1 = 300 MW. G2: 300 MVA rating, R2 = 0.02 pu (on the 300 MVA base), initial output P2 = 200 MW. G3: 300 MVA rating, R3 = 0.03 pu (on the 300 MVA base), initial output P3 = 200 MW. The frequency of the system is 60 Hz. Assuming D = 0 pu and using a common base of 1000 MVA, what is the new steady-state frequency for a load increase of 100 MW? Select one: O a. None of these O b. 59.96 Hz O c. 58.75 Hz O d. 59.88 Hz
What is the maximum length in km for a 1-phase transmission line having copper conductor of 0-875 cm2 cross-section over which 220 kW at unity 6. factor and 3500V delivered? power transmission is 80%%. Take specific resistance as 1.825 µ Q cn. at are to be The efficiency of
THESE ARE THE QUESTIONS FROM THE SUBJECT POWER SYSTEM FUNDAMENTALS AND THE CHAPTER IS PERFORMANCE OF TRANSMISSION LINES AND THE TOPIC IS SHORT TRANSMISSION LINES THE ANSWERS ARE GIVEN WITH THE QUESTION PLEASE DO ALL THE QUESTIONS PROPERLY „DONOT SKIP ANY STEP AND DO YOUR BEST 4.) Estimate the distance over which a load of 15000 kW at 0-85 p.f. can be delivered by a 3-phase transmission line having conductors of steel-cored aluminium each of resistance 0-905 O/phase per kilometre. The voltage at the receiving end is to be 132 kV and the loss in transmission is to be 7-5% of the load. [69-55 km] 5). A 3-phase line 3 km long delivers 3000 kw at a p.f. 0-8 lagging to a load. The resistance and reactance per km of each conductor are 0-40 and 0-3 Q respectively. If the voltage at the supply end is maintained at 11 kv, calculate: (i) ceceiving end voltage (line-to-line) (ii) line current (ii) transmission efficiency. [(i) 10.46 kv (ii) 207 A (ii) 95%] 6). A short 3-0 transmission line with an…
A high-voltage power line is made of aluminum conductor steel reinforced (ASCR) material. Suppose a power line has a radius of 2.00 mm and assuming the resistivity of the ACSR is 23.50 x 10^-9 resistor x m, how long is this powerline if it dissipates (on average) 350 MW with a maximum voltage across the powerline of 345,000 Volts (DC)?
Sub:electrical distribution
Vbase_zonel Sbase_zonel . * For the power system shown in Figure Q1b, calculate the per unit impedances of all components with given zone 1 voltage base 22kV and power base 100 MVA (for the system). = 22 kV = 100 MVA Generator: . YG₁ Zone 1 100 MVA 22 kV (0.1+ j0.5) pu 1 . E 1 T₁ YY Transformer 1: 100 MVA 25/130 kV (0.1+j0.5) pu Zone 2 L = (10+j100) S2 Figure Q1b. T₂ Zone 3 YA Transformer 2: 50 MVA 110/33 kV (0.1+j0.5) pu M₂Y Load (motor): ● 50 MVA . 33 kV (1+j0.5) pu
Answer it with complete explanation.....
The subject EE463 Power Systems analysis Please show all steps , and in clear writing it is better in hand written form.
Q2: Draw the single line diagram of a substation having the following equipments:(1) Incoming lines: Two, 400kV(2) Outgoing lines: (a) Two 400kV, (b) four, 132kV (C) Three, 33kV(3) Transformers: (a) Two 250MVA, 400/123KV D/Y11 (b) One, 25MVA, 132/33kV,D/Y11 (C) One, 2MVA, 33kV/ 420V,Y/Y(4) Bus-bars: 400KV Duplicate bus-bar, 132 kV-Duplicate bus-bar, 33kV single bus-bar,0.42KV single bus-barShow the positions of necessary equipments that using for protections, measurements andcommunications.