A bar of aluminum alloy of rectangular section75 mm x 20 mm and 800 mm long is stretched by an axial force of 150 kN. Find the volumetric strain, the actual change in volume and the percentage reduction in cross – sectional area of the bar. Take E = 70 GN/m2 and v = 0.34

A bar of aluminum alloy of rectangular section75 mm x 20 mm and 800 mm long is stretched by an axial force of 150 kN. Find the volumetric strain, the actual change in volume and the percentage reduction in cross – sectional area of the bar. Take E = 70 GN/m2 and v = 0.34

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.15P

See similar textbooks

Related questions

Q: 1. A steel rod 500mm long and 20mm× 10mm in cross-section is subjected to axial pull of 300 KN.If…

Q: Q3) The rigid bar ABCD is supported by bars (1) and (2). After load P is applied, the normal strain…

A: Given that, The strain in bar 1, ε1=20 μm/m, The deflection in bar 1 is, Strain in bar 1 is given…

Q: Two round rods, one of steel, the other of brass, are joined end to end. Each rod is 0.5 m long and…

A: Given that, Esteel=20×1010PaEbrass=10×1010Pa

Q: The stress strain curve determined from a sample of material is shown in the figure. The original…

Q: Find the strains in the 1-2 coordinate system (local axes) in a unidirectional boron/epoxy lamina…

A: Given data: Standard data for boron/epoxy is

Q: A rigid steel bar is supported by three rods, as shown. There is no strain in the rods before the…

Q: When a brass rod of diameter 2 mm is subjected to a tension of Sx10 N, the diameter changes by…

Q: The strain in the x-direction at point A (shown in fig.) on the steel beam is measured and found to…

A: Given, εx = 139 x 10-6 E = 204 GPa ν= 0.3

Q: Compound axial member ABC has a uniform diameter of d = 1.45 in. Segment (1) is an aluminum [E₁ =…

Q: 2-4 Which of the aluminum alloys shown in Figure 2-21 would you choose to obtain (a) Maximum…

A: Strength: The ability of the material to sustain any applied load without any failure is called…

Q: A bar of a uniform cross section is subjected to uniaxial tension and develops a strain in the…

A: Given data:- A bar of a uniform cross-section strain in x direction =1/800 μ= 1/3 To find:-the…

Q: the block is made of the material having linear elastic, perfect plastic behavior with constants of…

Q: Problem F2 stress (ksi) 130 120 110 100 90- 80 70 60 50 40 30 20 10 0 0.000 0.025 0.050 0.075 0.100…

A: The elastic modulus is E=29000 ksi. The diameter of the cylindrical specimen is d=2 in

Q: is shown below, 400 300 200 100 Stress (MPa)

A: 1.Modulus of elasticity can be obtained by taking the slope of stress-strain curve in elstic…

Q: The rigid beam is supported by a pin at A and wires BD and CE. Figure 3 m 2m 1 of 1 4 m ▾ Part A If…

A: Given data Downward displacement of C = 8mm Find the normal strain in CE and BD

Q: 3. A force P is applied to the rigid lever arm ABC as shown. The arm rotates counterclockwise about…

A: An axially loaded bar undergoes change in length, becoming longer when in tension and shorter when…

Q: Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1)…

Q: A steel plate is subjected to a state of plane stress (E = 200 GPa and v = 0.29) of xx = 105 MPa,…

A: Given Data: Young's Modulus E=200 Gpa=200000 Mpa μ=0.29 σx=105 Mpa σy=-19 Mpa τxy=96 Mpa

Q: A 2.0-m-long wire stretches 1.0 mm when subjected to a load. What is the tensile strain in the wire?…

A: GivenLength of wire L=2m∆L=1mm=1×10-3 m

Concept explainers

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
The strains for an element of material in plane strain (see figure) are as follows: x = 480 ×10-6. y = 140 × l0-6, and xy = —350 x 10”. Determine the principals strains and maximum shear strains, and show these strains on sketches of properly oriented elements.
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
A circular aluminum tube of length L = 600 mm is loaded in compression by forces P (see figure). The outside and inside diameters are d2= 75 mm and d1= 63 mm, respectively. A strain gage is placed on the outside of the lube to measure normal strains in the longitudinal direction. Assume that E = 73 GPa and Poissons ratio is v = 0.33. (a) IF the compressive stress in the tube is 57 MPa, what is the load P? (b) If the measured strain is e = 78 J X 10-6, what is the shortening
A prismatic bar in tension has a length L = 2.0 m and cross-sectional area A =249 mn2. The material of the bar has the stress-strain curve shown in the figure. Determi ne t he elongation 5 of the bar for each of the following axial loads: P = 10 kN, 20 kN, 30 kN, 40 kN. and 45 kN. From these results, plot a diagram of load P versus elongation 5 (load-displacement diagram).
An aluminum bar subjected to tensile Forces P has a length L = 150 in. and cross-sectional area A = 2.0 in2 The stress-strain behavior of the aluminum may be represented approximately by the bilinear stress-strain diagram shown in the figure. Calculate the elongation S of the bar for each of the following axial loads: p = 8 kips, 16 kips. 24 kips, 32 kips, and 40 kips. From these results, plot a diagram of load P versus elongation S (load-displacement diagram).
The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is/p = 0.5 in, its length is L = 30 in, and its thickness is/ = 0.5 in. Shear force of I' = 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.