The strain in the x-direction at point A (shown in fig.) on the steel beam is measured and found to be ɛx = 139 x 106. The shear strain at point A is found to be yxY = Rx 10 radians. The magnitude R is given by: (Take E= 204 GPa and Poisson's ratio =0.3). The cross-section of the beam is rectangular with depth 400mm and width 200mm respectively 100m 40omm 400m 600mın 1000 mm 200mm

The strain in the x-direction at point A (shown in fig.) on the steel beam is measured and found to be ɛx = 139 x 106. The shear strain at point A is found to be yxY = Rx 10 radians. The magnitude R is given by: (Take E= 204 GPa and Poisson's ratio =0.3). The cross-section of the beam is rectangular with depth 400mm and width 200mm respectively 100m 40omm 400m 600mın 1000 mm 200mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown, a cantilevered beam of length L = 5 m is fixed at A. It has a moment of M = 35.0 kN⋅m applied at B and a diameter of d = 600 mm. The normal strain distribution of an isolated segment of the beam is shown. If c = 300 mm, y = 214 mm , and ρ = 3 m , what is the maximum normal strain ϵmax in the beam?
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.9 mm and upward by v=4.9 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 730 mm, a = 22°, and ß = 68° U Answer: y = i P a B R urad
Atimber beam is subjected to loads as shown in the following figure If the allowable tensile and shear stresses forthe used timber are 14 MPa and 0 8 MPa respectively Find the depth ( of the beam Here A=5KN/m B=5KN
Find the strain Initial length=102.78 mm Change in length=0.004
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 2.6 mm and upward by v = 5.2 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 620 mm, a = 29°, and B = 61°. 41 Answer: y = i urad
Athin rectangular polymer plate PQRS of width b = 429 mm and height a = 140 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 1.6 mm and corner R is displaced leftward by the same amount. Determine the shear strain at corner P after deformation. a Y = y i b Q S a X urad
Find the Initial length Strain=0.00045 Change in length=23 mm
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 2.0 mm and upward by v = 4.2 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 775 mm, a = 20%, and B = 70% ↑= Answer: y = i P a B R urad
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 2.8 mm and upward by v = 5.6 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 620 mm, a = 26°, and B = 64° Answer: y = i P a B R urad
Please correct solution
For the cross-section shown in Figure 2, determine the location of the shear center (e = 100mm 10mm V 6mm 190mm Shear Center e 10mm Figure 2