A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Using the data given in the table, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Take x= 32 mm. Modalus of elasticity Allowable stress Aluminum Brass Aluminum 70 GPa 100 MPa 10 mm x 10 mm Brass 105 GPa 160 MPa 10 mm The largest permissible bending moment when the composite bar is bent about a horizontal axis is kN-m.

A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Using the data given in the table, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Take x= 32 mm. Modalus of elasticity Allowable stress Aluminum Brass Aluminum 70 GPa 100 MPa 10 mm x 10 mm Brass 105 GPa 160 MPa 10 mm The largest permissible bending moment when the composite bar is bent about a horizontal axis is kN-m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The composite bar shown is fixed at the ends and is subjected to the axial load P shown. If the aluminum is stressed to 10 ksi, find the force P and the stress in the steel. 10in. 15in. Aluminum Steel A=1.5 in? E=10x10°psi A=2.0 in? 6 E=30x10°psi 6
The composite bar is initially stress-free. Calculate the stress in each material and indicate tension or compression if the temperature has increased to 25°C. Consider that the walls are unyielding and suitably braced to prevent buckling. Use 2 decimal places.
SOLVE COMPLETELYINCLUDE FIGURES AND DIAGRAMS INCLUDE FORMULA
Problem: In the composite section as shown in figure 1, determine the following.1. The value of x̄2. The value of ȳ3. The moment of inertia with respect to Neutral x-axis
i need the final answer quickly pls
An element representative of a composite comprising an isotropic fiber enveloped by the isotropic resin is shown in Figure 1. Note that the two materials stick together perfectly and that the external surface of the element is free of stress. Calculate the axial stress in the fiber (of) and that in the resin (om) in the middle of the axis longitudinal fiber (L/ 2) using the material strength approach in the case where the element is exposed to a change in temperature AT, depending on following variables The thermal expansion coefficients af and am • The Af and Am sections • The moduli of elasticity Ef and Em • AT Guide: There is no external force • Relations to consider: balance, geometric compatibility and relation stress-strain. Fibre : At, Er, Of, af Matrice : Am, Em, Ớm, đm
3.* Figure 3 shows a tapered glued joint between two pieces of wood subjected to a tensile force. If the glue can sustain a maximum average tensile stress of 30 MPa and/or a maximum average shear stress of 50 MPa, what is the maximum angle that will permit the joint to transmit a tensile force F = 25 kN with a safety factor of 3.0? [Ans: 23⁰] F 1.6 A 3.4 Ө all dimensions in cm F
The composite bar in the figure is stress-free before the axial loads P1 and P2 are applied. Assuming that the walls are rigid, calculate the stress in each material if P1 = 150 kN and P2 = 90 kN.
The structural efficiency in managing bending, shear and for steel vs concrete
Mechanics of Deformable Bodies Show complete and detailed solution. Write legibly. Draw illustrations. Follow the decimals places on the direction
A composite bar consists of aluminum and steel is held by rigid supports as shown. At 57°C, an axial load of 220 kN is applied to the assembly. Determine the stresses in each of the component when the temperature is raised to 112°C. Based on laboratory results for steel, E = 210 GN/m?, a = 24x106/C, and for aluminum, E = 70 GN/m?, a = 11.8x10- 6/°C. STEEL Ø = 15cm? ALUMINUM Ø= 1Ocm? 220 kN -100 mm 150 mm Activa Go to S
A composite beam made of steel and bronze has the cross section shown. The cross-sectional dimensions are b, - 0.9 in, b2 - 2.7 in., and d- 1.8 in. The elastic modulus of the steel is E, - 30,000 ksi, and its allowable bending stress is 17 ksi. The elastic modulus of the bronze is E2 - 15,000 ksi, and its allowable bending stress is 14 ksi. Calculate the allowable bending moment that can be applied about the z centroidal axis. Bronze (2) d Steel (1) b2 Part 1 Your answer has been saved. See score details after the due date. Determine the modular ratio in order to transform the steel into an equivalent amount of bronze. Answer: n- Attempts: 1 of 1 used Part 2 Determine the area moment of inertia of the transformed section about the z-axis. Answer: in.4