What will be the moment of resistance of the composite section shown in the figure below if the permissible stress in wood and steel is 70 N/mm² and 120 N/mm² respectively. Steel plate Wood -200 4150 400 10

What will be the moment of resistance of the composite section shown in the figure below if the permissible stress in wood and steel is 70 N/mm² and 120 N/mm² respectively. Steel plate Wood -200 4150 400 10

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter14: Material Selection

Section: Chapter Questions

Problem 3ETSQ

See similar textbooks

Related questions

Q: Calculate the axial deformation of the Brass cylinder section (BC) shown in Figure 8. The…

A: Cross sectional area of steel, Cross sectional area of brass, Modulus of elasticity of steel,…

Q: A composite beam is made of two brass [E = 110 GPa] bars bonded to two aluminum [E = 71 GPa] bars,…

A: Bending moment=260Nm a=10mm b=85mm c=20mm d=55mm

Q: A composite bar is made by connecting a steel bar with a length of Lst = 300 mm and an brass bar…

A: Steel Length of steel Bar(L1) = 300 mm Elastic modulus(E1) = 200 GPa Coefficient of Thermal…

Q: Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The…

A: here m ,modular ratio is m = Esteel/ E another now , width of brass is 40/ mnow widht barss is 20mm…

Q: 7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses…

A: Given Data: The diameter of the solid aluminum cylinder is d1=3 in. The diameter of the steel tube…

Q: In the connection shown, 1/4-in. side and end fillet welds are used to connect the 3-in.-by-1 in.…

Q: A composite beam is constructed using a steel plate (14 mm x 125 mm) with two wood beams (75 mm x…

Q: For the tensile steel ratio P 0.0376, yield strength of reinforcing steel fy 500 MPa, fe 40 MPa,…

A: Given Steel ratio ρ=0.0376and stress in concrete fc'=40 MPa and stress in concrete fsy'=500Mpa…

Question

What will be the moment of resistance of the composite section shown in the figure below if the
permissible stress in wood and steel is 70 N/mm² and 120 N/mm² respectively.
Steel
plate
Wood
-200
4150 400
10

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data-

VIEW

Step 2: Calculation-

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The frame of a space shuttle type vehicle must have a high yield strength and high stillness, and the most important design factor is weight. Of all the materials presented in this chapter, what material might be the most suitable for the frame of a space shuttle? Assume that there will be both tensile and compressive stresses. For a space shuttle, cost is not a limiting factor. (a) You can eliminate entire classes of materials from consideration with a brief statement about their unsuitability. (b) What material has the highest specific yield strength? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (c) What material has the highest specific elastic modulus? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (d) Compare the materials with the highest specific yield strength and highest specific elastic modulus for suitability in the space shuttle frame. (C) Discuss the suitability of the top-rated material for this design from the viewpoint of the ability to produce a frame.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
In Example Problem 12.1, a uniaxial composite material is made into a circular rod Vbith a 1.27-cm diameter from 70 volume percent continuous carbon fibers and 30 volume percent epoxy. The rod is subject to an axial force of 100,000 N. The composite matcrial in Example Problem 12.1 is to be replaced with a less expensive composite made of 70 volume percent continuous E-glass fibers and 30 volume percent epoxy. The elastic moduli are 5 GPa for the epoxy resin and 72.4 GPa fos the E-glass. (a) Compare the elastic modulus, composite strain, fiber and matrix stresses, and density of this composite with the carbon epoxy composite in Example Problem 12.1. Usc the density of UHM carbon, and assume the density of the epoxy is 1.2g/cm3 . (b) Can both the E-glass fiber and matrix withstand the applied force?