A wcod beam rainforced by an aluminum channel section is shoun in the figure. 150 mm 230 mm 38 mm 65 mm 163 mm The beam has a cress section of dimensions 150 mm x230 mm, and the channel has a uniform thickness of 6.5 mm. the alowable stresses in the wood and aluminum are M and b MPa, respectively, and if their moduli of elasticity are in the ratie I to o, what is the maximum allewable bending moment for the beam? Enter the magnitude in km (Assume that the component part of the beam atre securely bended by adhesives or connected by fasteners Alse, be sure to use the trantformed-section method in the solution.) (No Responne 14.00 k m

A wcod beam rainforced by an aluminum channel section is shoun in the figure. 150 mm 230 mm 38 mm 65 mm 163 mm The beam has a cress section of dimensions 150 mm x230 mm, and the channel has a uniform thickness of 6.5 mm. the alowable stresses in the wood and aluminum are M and b MPa, respectively, and if their moduli of elasticity are in the ratie I to o, what is the maximum allewable bending moment for the beam? Enter the magnitude in km (Assume that the component part of the beam atre securely bended by adhesives or connected by fasteners Alse, be sure to use the trantformed-section method in the solution.) (No Responne 14.00 k m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: (d) Check the minimum steel requirements A, criteria 1 = min in? A min criteria 2 = in? in?…

Q: 200 x 20 mm Plate • 5310 x 47.3 C310 x 30.8 Semi-circle Weld, 10mm radius

Q: A steel bar is attached to a wood support beam with four 22 mm diameter lag screws, as shown in the…

A: Given Diameter of screw, d = 22 mm Number of screws, n = 4 Width of steel bar, b = 69 mm Thickness…

Q: Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The…

A: here m ,modular ratio is m = Esteel/ E another now , width of brass is 40/ mnow widht barss is 20mm…

Q: 7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses…

A: Given Data: The diameter of the solid aluminum cylinder is d1=3 in. The diameter of the steel tube…

Q: pecify a suitable aluminum casting alloy for a bar with square crosssection. Length of one side of…

A: Given:- The length of the one side of the cross-section= 50 mm The value of the tensile load = 60 kN…

Q: A composite beam made of steel and bronze has the cross section shown. The cross-sectional…

A: To find the modular ratio for transforming steel to bronze n…

Q: A composite beam made of steel and bronze has the cross section shown. The cross-sectional…

Q: 2. A column HP 14 x 102 of A572 Gr. 55 steel has a length of 15 ft is fixed at both ends. Compute…

Q: What will be the moment of resistance of the composite section shown in the figure below if the…

A: A composite beam section as shown in the below figure-Permissible stress in wood & steel-To…

Q: A composite beam is made of two brass [E = 105 GPa] plates bonded to an aluminum [E = 63 GPa] bar,…

A: Given data Eb = 105 GPA EAl = 63 GPA M= 1525 Nm = 1525 × 103 N-mm

Q: Aluminum A = 1.25 in.? E = 10 x 106 psi Steel A = 2.0 in.2 E= 29 x 10° psi 15 in- -12 in.-

A: The given data is: For Aluminum bar: Length = 15 in Area = 1.25 in2 Modulus of Elasticity (E) = 10 x…

Q: A composite beam is made of two brass [E = 119 GPa] plates bonded to an aluminum [E = 73 GPa] bar,…

Concept explainers

Composite Construction

Composite construction is the construction of structures in which two or more materials are used. Regarding structural engineering, composite construction is a construction where two materials are bound together in a technical manner such that both the materials act as a single unit to carry and transfer the load. The motives of composite construction are to increase the structural strength, make structures more aesthetic, and provide a sustainable environment.

Question

A wood beam reinforced by an aluminum channel section is shown in the figure.
150 mm
230 mm
38 mm
6.5 mm
-163 mm-
The beam has a cross section of dimensions 150 mm x 230 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 MPa and 50 MPa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam? Enter the magnitude in kN · m. (Assume that the component parts
of the beam are securely bonded by adhesives or connected by fasteners. Also, be sure to use the transformed-section method in the solution.)
(No Response)
14.06 kN· m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

How to solve for the centroid of the composite body using the principle of moments and treat each part as a finite element of the whole figure (Show a step by step solution)
A composite beam made of steel and bronze has the cross section shown. The cross-sectional dimensions are b1 = 0.5 in, b2 = 1.5 in., and d = 1.0 in. The elastic modulus of the steel is E1 = 30,000 ksi, and its allowable bending stress is 24 ksi. The elastic modulus of the bronze is E, = 15,000 ksi, and its allowable bending stress is 16 ksi. Calculate the magnitude of the allowable bending moment that can be applied about the z centroidal axis. y Bronze (2) Steel (1) bị b2 Answer: M = i Ib-in. Save for Later Attempts: 0 of 1 used Submit Answer
What is the manufacturing tensional yield strength (lbf) of grade S135 drill pipe? a. This is a trick question because drill pipe size is not provided b. The answer can’t be calculated because the length of the pipe is not given c. The yield strength is 135000 psi and is a property of the steel d. The yield strength is 135000 psi and depends on the cross-sectional area
Two pieces of wood, 60 mm by 120 mm each are glued together along the 40° joint. The permissible normal stress in the glue is limited to 100 MPa. The maximum safe load that can be applied at the joint is P+ 40° 60 mm P