A balanced, three-phase, positive sequence, with grounded neutral source, supplies power to a balanced delta connected load. For the system, additional information are as follows: Vbc = 443 cis 191 degrees volts; and Ic = 10.5 cis99 degrees amperes What is the value of the total real power of the delta load in watts?

A balanced, three-phase, positive sequence, with grounded neutral source, supplies power to a balanced delta connected load. For the system, additional information are as follows: Vbc = 443 cis 191 degrees volts; and Ic = 10.5 cis99 degrees amperes What is the value of the total real power of the delta load in watts?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23MCQ: In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the...

See similar textbooks

Similar questions

Two reverse parallel scr are used to control the voltage on a 10 ohm load over a 230V, 50HZ 1- phase AC source, and triggering is done at 3O degrees for positive alterance. Calculate the effective (rms) voltage on the load. a) 230.34V b) 226.64V c) 220V d) 110.56V e) OV
The Circuit diagram for a power system is shown in Figure Q2. A synchronous generator consists of voltage source, in rms, (Van = 110 20° V, Van = 110 2-120° V and Ven = 110 -240° V). The transmission line has an impedance (Zine) of 0.05 + j0.10 O per phase, and the load has an impedance (Z.) of 12 + j6 0 per phase. line Von line Z, V. cn bn В lin Figure Q2 a. As an electrical engineer, explain about the power system in Figure Q2 with respect to the voltages, and the connection for the source and the load. Give at least FOUR (4) points. b. Solve the followings: i. the line currents. ii. the real, reactive and apparent powers consumed by the load per phase.
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
P2. A 100 volts rms single-phase voltage source feeds an inductive load of (30+j40) 2. Determine the value of capacitance to bring the power factor of the source to unity.
Describe the concept of three-phase power in electrical systems and its advantages over single-phase power.
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
How does a three-phase power system differ from a single-phase power system, and what are their respective applications?
7
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
As per bartleby honor code I can submit 3 questions. Please solve b,d and e
Hi, Help me with this circuit question
Four conductors meet at a junction. the current are i1= 5sinwt, i2= 3sin(wt + 90) and i3= 2sin(wt-90). calculate the rms value of i4.