A d.c. serier generator, having an external characteristic which is a straight line through zero to 50 V200 A is connected as a booster between a station bus bar and a feeder of 0.3 ohm resistane. Calculate the voltage difference between the station bus-bar and the far end of the feeder a current of (i) 200 A and (ii) 50 A.

A d.c. serier generator, having an external characteristic which is a straight line through zero to 50 V200 A is connected as a booster between a station bus bar and a feeder of 0.3 ohm resistane. Calculate the voltage difference between the station bus-bar and the far end of the feeder a current of (i) 200 A and (ii) 50 A.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Related questions

Q: There are 160 slots in a 3-phase, 8-pole, 50 Hz., star connected alternator. There are 4 conductors…

Q: A shunt generator supplies a load of 5,500 W at 110 V through a pair of feeder conductors having a…

A: For better understanding I draw the single line diagram of the given system then we find the emf…

Q: In a single-phase alternator, a given field current produces an armature current of 250 A on…

Q: The section bus-bars A and B are linked by a bus-bar reactor rated at 5000 kVA with ?? % reactance.…

Q: A dc 4 pole lap wound generator is running at 1000 rpm having 1200 conductors and flux density is 10…

A: Given that A dc Lap wound generator having total conductor Z = 1200 speed or number of revolution…

Q: A generator at no-load operates 61 Hz, slope 1MW/Hz. Load 1= 1.0 MW and load 2=0.8MW are connected.…

A: In this question we need to choose a correct option

Q: What are harmonic producing loads and how these loads affect the power quality

A: Harmonics are explained as the characteristics of a voltage or current waveform with relation to its…

Q: 3. A 4-pole 3-phase 60HZ wye-connected alternator having 60 slots with 2 conductors per slot in 2…

A: Per phase emf = 4.44×frequency×flux per pole×turns per phase×winding factor. for star connection ,…

Q: An Armature runs at 250 r.p.m. and generates an e.m.f. at 50 Hz. There are 216 slots each…

A: The information provided in question are:

Q: A single phase, 2000 V alternator has armature resistance and reactance of 0.8 ohms and 4.94 ohms…

A: Given, A single phase alternator has V= 2000 V R= 0.8 ohms X= 4.94 ohms I= 100 A Power factor,…

Q: A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The…

Q: A synchronous generator runs at 250 rpm and generates at 50-Hz. There are 216 slots, each containing…

A: In this question, We need to Find the emf induced in each phase winding and the terminal voltage?…

Q: Determine the power angle characteristic for the system shown in figure. The generator is operating…

Q: Two identical three – phase Y – connected alternator A and B share equally a load of 10MW at 33kV…

Q: 1-Adiust the function generator to give (10 v p.p )(170) Hz.

A: Step 1:To adjust a function generator to output a 10 V peak-to-peak sine wave at 170 Hz, you…

Concept explainers

Magnetic Moment

The magnetic moment is defined as the alignment of a magnet and its strength when the magnet is creating a magnetic field. There are number of examples of the magnetic moment, few are a current carrying conductor in the form of coil, elements at microscopic levels like electrons and many more.

Question

A d.c. serier generator, having an external characteristic which is a straight
line through zero to 50 V 200 A is connected as a booster between a station bus bar and a feeder
of 0.3 ohm resistane. Calculate the voltage difference between the station bus-bar and the far end
of the feeder qa current of (i) 200 A and (ii) 50 A.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

AT CURRENT OF 200 A

VIEW

AT 50 A CURRENT

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the power angle characteristic for the system shown in figure. The generator is operating at a terminal voltage of 1.05p.u. and the infinite bus is at 1.p.u. voltage. The generator is supplying 0.7p.u power to the infinite bus. Draw the power angle curve in graph sheet. 0.1 0.3 Generator 0.2 Infinite 0.3 bus ele
A generator at no-load operates 61 Hz, slope 1MW/Hz. Load 1= 1.0 MW and load 2=0.8MW are connected. Find the frequency before and after adding the load 2. (Using House Diagram)A. 60 Hz & 59 Hz C. 60 Hz & 59.2 HzB. 60 Hz & 59.1 Hz D. 60 Hz & 59.3 Hz
D2. When a generator's full-load output voltage is the same as its no-load output voltage it is said to be a) under-compounded b) flat-compounded c) over-compounded d) none of the above D3. The output of an overcompounded DC generator can be lowered by use of a a) rheostat connected in series with the series field b) rheostat connected in parallel with the series field c) rheostat connected in parallel with the shunt field d) none of the above D4. When might it be desirable to use an overcompounded generator? a) never b) always c) to compensate for line loss d) when you need a higher no-load voltage than your full-load voltage
Figure 1 shows an electric generator with 3 rotor windings as marked by a-1, b-2 and c-3. A permanent magnet is placed in the middle of the rotor with the rotational direction. The 3 rotor windings are connected through line to the three identical load resistors R₁, R₂ and R3 in Wye connection. The resulting currents in each line are la, lb and Ic. Design the generator-line-load connections, and propose the methodologies to construct 3-phase 3-wire connection. Use a diagram to justify your answers. D (0 N $1 Figure 1
A shunt generator supplies a load of 5,500 W at 110 V through a pair of feeder conductors having a resistance of 0.02 ohm each. The armature and shunt field resistances are 0.15 ohm and 50 ohms, respectively. Find the emf generated. (Write only the value without the unit) (Round-off to 2 decimal places) Round your answer to 2 decimal places.
A power station consists of two synchronous generators A & B of ratings 250 MVA and 500MVA with inertia 1.6 pu and 1.0 pu respectively on their own base MVA ratings. The equivalent pu inertia constant for the system on 100 MVA common base is:- (a) 2.6 (b) 0.615 (c) 1.625 (d) 9.0
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
A synchronous generator runs at 250 rpm and generates at 50-Hz. There are 216 slots, each containing 5 conductors arranged in a full-pitched winding for 3-phase star connection. All the conductors of each phase are in series and the flux per pole at no-load sinusoidally distributed over the pole pitch is 30 mWb. Find the emf induced in each phase winding and the terminal voltage.
The O.C.C. data for separately-excited generator when run at 130 r.p.m. on open circuit is E.M.F. (V) : 12 44 73 98 113 122 127 Exciting current : 0 0.2 0.4 0.6 0.8 1.0 1.2 Deduce the curve of e.m.f. and excitation when the generator is running separately-excited at 1000 r.p.m.To what voltage will the generator build up on no-load when running at 1000 r.p.m.? To what voltage will thegenerator build up on no-load when running at 100 r.p.m. if the total field resistance is 100 Ω ?
The reactance of a generator is given as 0.25 per-unit based on the generator’s of 18 kV, 500 MVA. Find its per-unit reactance on a base of 20 kV, 100 MVA. a. 0.0505 b. 0.0605 c. 0.0405 d. 0.0606
What is practical application of PWM?
Two 220 V dc generator each having linear external characteristic operate in parallel. One machine has terminal voltage of 270 V. On no load and 220 V at a load current of 35 A while the other has a voltage of 280 V at no load and 220 V at 50 A. Calculate the output current of each machine and the bus bar voltage when the total load is 60 A. What is the KW output of each machine under the condition?