A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed exactly at the 50 meter mark. The slope of the measured line is 1 degree and 30 minutes. The tension on the tape is 10 kg, and the weight of the tape per unit length is 0.05 kg/m. Determine the exact correction (m) to be applied due to slope if sag is neglected. need answers and solutions asap, thank you!

A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed exactly at the 50 meter mark. The slope of the measured line is 1 degree and 30 minutes. The tension on the tape is 10 kg, and the weight of the tape per unit length is 0.05 kg/m. Determine the exact correction (m) to be applied due to slope if sag is neglected. need answers and solutions asap, thank you!

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter4: Mechanical Processes

Section: Chapter Questions

Problem 4.21P

See similar textbooks

Similar questions

Need it asap please answer this, thankyou.
18
3. A 30-m steel tape that is standardized at a temperature of 18°C and under a pull of 8 kg. The measured length of a line using this tape was 1602 m under a pull of 12 kg. The temperature during the measurement was 26°C. The tape was supported only at the ends of every 30 m length during the measurement. The tape has a cross-sectional area of 0.04 cm², Modulus of Elasticity of 2.1 x 106 kg/cm², coefficient of thermal expansion of 0.000012/°C, and a unit weight of 0.0077 kg/cm³. Determine the corrected length of the line.
Show solution in each question
Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when 0 = 35° and P= 196 N. Given: Ms = 0.20 and Hk = 0.15. The block is not in equilibrium? The magnitude and direction of the friction force is ? Note: I need correct answers please so double check your working out. And show everything in relation to the question.
Determine the proportional shear stress for a material that has a modulus of rigidity of 30 GPa and proportional shear strain of 0.0001. Select one: O a. 30 x 10 Pa © b.0.003 Pa C. 30 x 10 Pa 13 Pa G d. 30 x 10
A steel rectangular block 1in wide, 1/2in deep and 4in long is subjected to an axial tensile load of 10.5kips. Measurements show the block to increase in length by 2.8x10^-2 in and to decrease in width by 0.21x10^-2 in. a. Determine the Poisson’s Ratio of the material. b. Determine the Modulus of Elasticity of the material.
Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine when in operation and provide a stress analysis on the piston .use a factor of safety of 5. Assume outside temperature (bottom plate) is -233 degC and an internal PC board (top plate) is 85 degC ? wwbewn Figure 1.1 show measurement to help you to find the volume / Area Ø1.50 Ø8 Ø 10 - Show your calculations and the analysis and find the applied load on it
I need the answer as soon as possible
A line was found to be 2865.35m long when measured with a 30-m tape under a steady pull of 6.5kg at a mean temperature of 30°C. Determine the correct length of the line if the tape used is of standard length at 20°C under a pull of 5.5kg. Assume the cross-sectional area of the tape to be 0.025cm2, elastic modulus as 2.10x10°kg/cm², and coefficient of thermal expansion to be 11.6x10-/°C.
show all details please
provide correct answer asap with FBD