Item 1Replace the loading system by an equivalent resultantforce and couple moment acting at point A. AssumeF = 130 lb, F,= 60 lb and F3180 lb (Figure 1)Part ADetermine the magnitude of the resultant force.Express your answer to three significant figures and include the appropriate units.µAFR =ValueUnits%3DSubmitRequest AnswerFigureC 1 of 1Part B13Determine the angle between the resultant force and the x axis4.Express your answer using three significant figures.ftF2vec3 ft--3 ft13counted counterclockwise from positiveaxisSubmitRequest AnswerO G ) ENG3.

Given F1=130lb F2=60lb F3=180lb

m 1 Replace the loading system by an equivalent resultant Force and couple moment acting at point A. Assume F = 130 lb, F= 60 lb and F = 180 lb (Figure 1) Part A Determine the magnitude of the resultant force. Express your answer to three significant figures and include the appropriate units. ? FR = Value Units Submit Request Answer igure 1 of 1 Part B F, Determine the angle between the resultant force and the z axis. Express your answer using three significant figures. 1 ft Vol AEo IT vec 3 ft counted counterclockwise from positive %3D axis Submit Request Answer O G 4) ENC

m 1 Replace the loading system by an equivalent resultant Force and couple moment acting at point A. Assume F = 130 lb, F= 60 lb and F = 180 lb (Figure 1) Part A Determine the magnitude of the resultant force. Express your answer to three significant figures and include the appropriate units. ? FR = Value Units Submit Request Answer igure 1 of 1 Part B F, Determine the angle between the resultant force and the z axis. Express your answer using three significant figures. 1 ft Vol AEo IT vec 3 ft counted counterclockwise from positive %3D axis Submit Request Answer O G 4) ENC

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 6 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! Determine the normal stress and change in length of the aluminum rod if the temperature was raised by 12Q°C. The 0.5-mm gap exists at 2T°C.
B2
Using τall = 71 MPa and G = 27 GPa, determine for each of the aluminum bars shown the largest torque T that can be applied and the corresponding angle of twist at end B. Refer to Table 3.1. The largest torque that can be applied at end B of bar a is N·m and the corresponding angle of twist is °. The largest torque that can be applied at end B of bar b is N·m and the corresponding angle of twist is °.
2. A concrete beam is shown below. A. Determine the magnitude of the resultant force acting on the beam (2 decimal places) B. The distance of resultant force from the left edge (3 decimal places) C.If the loads will be replaced by a single force located at the left edge, what moment must be paired with it (Clockwise positive) to be equivalent to the original loads? (2 decimal places) w, w, M Given W1 = 11 kN/m W2 = 14 kN/m %3D M = 4.3 kNm L1 = 4.1 m L2 =1.9 m
Mechanics of deformable bodies. Two decimal places.
Review Problem 4.8 Take that L = 13 ft. (Figure 1) Figure 1 of 1 L 800 lb/ft L > B Part A Replace the distributed loading by an equivalent resultant force. Express your answer to three significant figures and include the appropriate units. FR = Submit x = Submit Value kip μÀ Part B Specify the location of FR on the beam, measured from the pin at C. Express your answer to three significant figures and include the appropriate units. 0 μᾶ Value My Answers Give Up ft My Answers Give Up ? ? Provide Feedback Continue
The shaft is supported by a journal bearing at A and a thrust bearing at B. (Figure 1) Figure -6 ft- 3000 lb 2500 lb 75 lb/ft I pontot, -12 ft 1 of 1 2 ft Part A Determine the normal force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Nc = Submit Part B HÅ Submit Value Part C Request Answer Determine the shear force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Vc = Value μA Units Request Answer ? Units ? Review
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft (D= 2.25" and d=0.90''). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12x106 psi, 4x106 psi, and 6x106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the aluminum shaft.
Figure 23 1 of 1 Part A Determine the magnitude of the resultant force F-F₁+F₂ Assume that F₁ 275 lb and F-305 lb (Egure 1) Express your answer to three significant figures and include the appropriate units. FR437 Submit НА Part B lb Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining μA Determine the direction of the resultant force FR, measured counterclockwise from the positive z axis Express your answer to three significant figures and include the appropriate units. Value B ? P Pearson Units ?
The 62-mm-diameter steel shaft is subjected to the torques shown. (Figure 1) Figure 1 of 1 400 mm B 3 kN.m 600 mm 2 kN-m I GILM Determine the angle of twist of end A with respect to C. Take G=75 GPa. Express your answer to three significant figures and include the appropriate units. A/C= Submit μA Value Units My Answers Give Up ?
Two wrenches are used to tighten the pipe. The pipe is made from a material having an allowable shear stress of Tallow = 80MPa. The pipe has an outer diameter of 25 mm and inner diameter of 20 mm Figure 1 P of 1 250 mm B P Determine the allowable maximum force P that can be applied to each wrench. (Figure 1) Express your answer with the appropriate units. μA P = Value Submit Units My Answers Give Up ? Provide Feedback
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! Answer ASAP!