Consider the object shown in (Figure 1). Suppose that P = 310 N, M = 810 N. m. Follow the sign convention. Part A Determine the internal normal force at point C. Express your answer to three significant figures and include the appropriate units. ? Nc = Value Units Submit Request Answer Part B Determine the internal shear force at point C. Express your answer to three significant figures and include the appropriate units. HA ? Vc = Value Units Figure Request Answer < 1 of 1 Submit Part C Determine the internal moment at point C. Express your answer to three significant figures and include the appropriate units. 1m ? 1m 1 m 2 m Mc = Value Units

Consider the object shown in (Figure 1). Suppose that P = 310 N, M = 810 N. m. Follow the sign convention. Part A Determine the internal normal force at point C. Express your answer to three significant figures and include the appropriate units. ? Nc = Value Units Submit Request Answer Part B Determine the internal shear force at point C. Express your answer to three significant figures and include the appropriate units. HA ? Vc = Value Units Figure Request Answer < 1 of 1 Submit Part C Determine the internal moment at point C. Express your answer to three significant figures and include the appropriate units. 1m ? 1m 1 m 2 m Mc = Value Units

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Replace the loading acting on the beam (Figure 1) by a single resultant force. Suppose that F₁ = 500 N, F₂ = 340 N, and F3 = 750 N. igure F₁ 60° -2 m 4 m F₂ B -3 m F3 1500 N-m 1 of 1 Determine the magnitude of the resultant force. Express your answer to three significant figures and include the appropriate units. ► View Available Hint(s) F = Submit Part B 0 = Part C O x = Determine the angle between the resultant force and the x axis. Express your answer in degrees to three significant figures. ► View Available Hint(s) μА Value Submit VL ΑΣΦ Units μA Value ↓↑ vec Specify where the force acts, measured from B. Express your answer to three significant figures and include the appropriate units. ► View Available Hint(s) R ? Units ? ? counted counterclockwise from the negative x axis
Q#1: A block is shown in figure. Consider a compressive load is applied (one at a time) on all corners (A, B, C and D) of the block. This will cause each corner to be in a different state of stress under the action of load at different location. Discuss the effect of load on each corner under changing load locations. It is mandatory to consider the effects of direct stresses and bending stresses. (1
Determine the shear force 6.24 ft to the right of point A for the beam shown belowif T = 1195 lb ft, W = 199 lb/ft, a = 5.46 ft, b = 3.4 ft, and c = 3.4 ft. Round of the final answer (in lb) to four decimal places. W A D B a C T |— ³ · →|←▬▬▬ 9
The shaft is supported by a journal bearing at A and a thrust bearing at B. (Figure 1) Figure -6 ft- 3000 lb 2500 lb 75 lb/ft I pontot, -12 ft 1 of 1 2 ft Part A Determine the normal force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Nc = Submit Part B HÅ Submit Value Part C Request Answer Determine the shear force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Vc = Value μA Units Request Answer ? Units ? Review
4....2 Suppose that P=101lbs. What will the force Q be in this case?
QUESTION 4: Check whether the beam section whose loading condition, cross section and dimensions are given in the figure is sufficient. Also draw the shear stress diagram of the section next to the section.
Show FBD, all the step by step solution and neat handwritten.
Using Tall = 68 MPa and G= 27 GPa, determine for each of the aluminum bars shown the largest torque T that can be applied and the corresponding angle of twist at end B. Refer to Table 3.1. (a) (b) 45 mm 15 mm 25 mm 25 mm 900 mm B Check my work B The largest torque that can be applied at end B of bar a is N-m and the corresponding angle of twist is The largest torque that can be applied at end B of bar bis N-m and the corresponding angle of twist is
A rectangular steel block is 4 inches long in the x direction, 3 inches longin the y direction, and 4 inches long in the z direction. The block issubjected to a triaxial loading of three uniformly distributed forces asfollows: 48 kips tension in the x direction, 60 kips compression in the ydirection, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 ×106 psi, determine the single uniformly distributed load in the x directionthat would produce the same deformation in the y direction as the originalloading. Note provide a diagram/figure. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
Example: Member AB weighs 2000 N. Draw a free body diagram of AB. C.G. cord B