A 5 m long simply supported beam carries a superimposed load of 20 kN/m. Design the midspan section if its effective depth is kept constant at 50 cm using (i) elastic theory, (ii) ultimate load theory, and (iii) limit state theory. Neglect self weight of the beam. Use M 25 concrete and Fe 415 grade steel.

A 5 m long simply supported beam carries a superimposed load of 20 kN/m. Design the midspan section if its effective depth is kept constant at 50 cm using (i) elastic theory, (ii) ultimate load theory, and (iii) limit state theory. Neglect self weight of the beam. Use M 25 concrete and Fe 415 grade steel.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 8 m simply supported singly reinforced beam has a width of B= 39 cm and a height H=61 cm. Concrete compressive strength, f'c-30 MPa Steel Yield Strength of longitudinal bars, fyl-420 MPa, Steel Yield Strength of transverse bars, fyt -280 MPa, Unit weight of concrete, 24.4 kN/m³. Steel cover of the beam = 6 cm It is desired that the capacity of the beam to be at balanced condition. If the structural engineer wants the optimization ratio of the design moment and capacity to be 0.66, calculate the maximum value of the live load in kN/m to meet such condition Use NSCP2015
A T-beam for a floor system has a slab thickness of 75 mm and a web thickness of 375 mm. It has an effective depth of 600 mm. The beam carries a dead load moment of 280 kN-m and a live load moment of 525 kN-m. It has a span of 5.4 m and a spacing center to center of 1.8 m. Use reduction factor ø=0.90, fc’=20.7 MPa, fy = 344.7 MPa.Determine the effective width of flange. Determine depth of compression flange. Determine the required steel area. See the formula in the image
A channel shape is used to support the loads shown on the beam. The dimensions of the shape are also shown. Assume Lag 3 ft. Lac-9 - P-2050 lb, w-1200 lb/ft, b-12 in. d-5 in., t-0.875 in. Consider the entire 12-ft length of the beam and determine Determine the maximum compression bending stress at any location along the beam Answer in ksi rounded-off to 2 decimal places. Report the answers here using the correct signs. A LAB Add your answer B Luc Mort Last N
A reinforced concrete T-beam is to be designed for tension only. The beamwidth is 250 mm. effective depth to bottom bars is 400 mm, flange thickness is 100mm, simple span is 3.6 m and beam spacing is 1.2 m on centres. If the applied designmoment is 300 kn-m, fc’ = 20.7 MPa and fy = 414 MPa. Determine the effective widthof the compression flange and the number of 28 mmφ diameter bars necessary forthe beam.
Reinforce Concrete Design Determine the design moment capacity of the reinforced concrete beam shown inFigure 1(a) if it is reinforced with 4-28-mm diameter in tension and 2- 16-mmdiameter in compression. Use f’c = 21 MPa, fy = 276 MPa and effective cover of 50 mm for top and bottom bars.Assume the load W to be ultimate. Neglect weight of beam.
a beam b = 350mm h = 660mm is reinforced with 2- 28mm compression bars and 4- 36mm tension bar. concrete cover is 60mm from centroid of the bar, if The beam is subjected to a maximum service dead load of 230KN m. determine the maximum service live load the beam can carry. use fc = 21Mpa, fy = 345MPA Select the correct response: MII = 244.02KN-m MII = 390.43KN-m %3D MII = 666.43KN-m MII = 436.43KN-m
pre stressed conc. solution pls answer
Example 2.2-A simply supported reinforced beam has a cross section with a width of 500mm and a depth of 750mm, and a span of 15m. It carries a deadload of 20kN/m and an occupancy load of 4.8kN/m. It also carries a deadload of 20kN and a live load of 5kN located at 8m from the left support. The beam is made of normal density concrete. Determine the maximum factored bending moment in the beam, Mr, due to the applied factored loads.
Question 17
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of 18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis.
Reinforced concrete design plz answer the a and b with complete solutions.. thank you
Q1) The R.C slab system shown in Figure (1) supported by column line beams and carries a service live load of 5 kN/m and a service superimposed dead load of 3.5 kN/m in addition to its own weight. Slab thickness is 200mm, all beams are (300x600) mm. All columns are 300mm square, use f-25MPA and f=420MP.. According to the ACI-direct design method, determine the following: 6.0m 7.6m 6.0m (a) Design the middle strip bottom bars of the exterior indicated panel shown, in E-W direction. 6.0m 6.0m 7.6m (b)Design the required steel reinforcement at the exterior corner (C). Figure (1)