A 36/240 V phase transformer, belonging to a phase measured from the no-load (idle) run and short-circuit test. values ​​are given in the table below. High voltage by applying rated voltage to the low voltage winding (The winding ends were left unloaded and the results of the no-load test results were obtained. By applying nominal current to the high voltage windings, the low voltage windings were short-circuited, and the results of the short circuit test were obtained. In direct current test 1 V direct voltage is applied to the low voltage winding, and the transformer draws 500 A direct current. All equivalent Calculate the circuit elements as moved to the low voltage side. Idle run test: Voltage : 36V Power : 68W Current : 2,8A Short circuit test: Voltage : 15V Power : 325W Current : 42,2A

Q: If the secondary side of a dual-voltage single phase transformer, as per figure 1,  were to be…

A: The secondary side of a dual-voltage single phase transformer, as per the figure given in  the…

Q: (b) A three phase distribution transformer characteristics is shown in Table Q1(b). Referring to…

A: Formula to calculate efficiency of a transformer is: η=n×KVA×cosϕn×KVA×cosϕ+Pi+n2×PCUwhere, n is…

Q: and a full-load copper loss of 460 W. (a) The above transformer is to be connected as an auto…

A:

Q: b) A single phase 50 Hz, transformer with turns ratio of 25:1400 has cross sectional area of 110 cm2…

A:

Q: i need the answer quickly

A: In this question we need to find a equivalent impedance referred to primary side and draw it…

Q: 5. A 100-kVA, 3-phase, 50-Hz 3,300/400 V transformer is A-connected on the h.v. side and Y-connected…

A: Rating of transformer S = 100 KVA Frequency f = 50 Hz Voltage rating 3300/400 V Resistance at hv…

Q: iii. No-load current 3. If the ratio of V/F has been kept constant and the observed value of…

A: Q.1) Explanation 1)When the frequency is lowered (for slower motor speed), the magnetic field…

Q: TTR 300 , What is the method of connecting the device to the transformer ?

A:

Q: 1. The number of devices required to perform the no-load test and the short-circuit test for…

A: Electrical machines can be either generator, transformer or motors. They can be either Ac machines…

Q: What is the use of current transformer? Draw it's block diagram.

A:

Q: The idle operating current of the three-phase transformer connected to Yy0 (Y-Y) with a power of…

A: Given transformer with rating 6300 KVA and 15/0.4 KV The no load current I0=2.91No load active power…

Q: A fault occurs at point F of the system in the figure. Calculate the sub-transient current in phase…

A:

Q: Q3-(A)- Three single-phase, 50 kVA, 2310/ 230 V, 60 a 3-phase, star /delta, 4000/230V transformer…

A: NOTE- According to the policy, we can answer sub-parts of the first question, kindly post other…

Q: 1- The low voltage winding is wound under the high voltage winding. Why.

A: As per bartleby guideline for more than one question asked only first is to be answered please…

Q: 3.16 A single-phase, 50-k VA, 2400/240-V, 60-Hz distribution transformer has the following…

A: It is given that:

Q: The values ​​of a phase measured from the no-load (no load) operation and short circuit test of a…

A:

Q: (10 kVA, 200/20 V, 50 Hz values are written on the plate of a 1 phase transformer. The values given…

A: Given table,parameterOpen circuit test readingsV200 VA2.7 AW120 wattsAsked to find the Open circuit…

Q: Write the specification of transformer and voltage regulator of your circuit.

A: Step-1-> A transformer is an electrical device that is used to transfer electrical energy from…

Q: 4. The core loss of the single phase 2200/220-V, 50-Hz transformer is measured using the low-…

A: It is given that:ϕ=cos-10.1ϕ=84.16° voltmeter reading=240 VExciting current=1  AWattmeter reading=24…

Q: During routine tests of a three phase transformer, measurements of DC resistance between winding…

A: On a three phase transformer, various routine testes are carried out.  The various tests are…

Q: 1. From first principles, derive the per-phase equivalent circuit of a three-phase transformer…

A: As it is asked only solve subpart (c) so we are solving only that subpart. It is asked to draw the…

Q: What are the Losses of Transformer and how these losses are to be determined? In a transformer if…

A: Given that  I2 = 100A  I1 = 10A N2 = 5  N1 = 8

Q: Determine the required load resistance to operate the transformer of Q3(b) at maximum efficiency…

A: According to question: c) The turn ratio 'a' is calculated as ∵a=VpVs⇒a=23024⇒a≃10 The transformer…

Q: Q2 Find the elements of the equivalent circuit attributed to the secondary of a single-phase…

A:

Q: 1 ww ww F w Ju 2

A:

Q: Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer.…

A:

Q: 1- The resistance of secondary windings of step-down transformer is resistance of secondary…

A: Need to fill the blank

Q: 1. Explain why transformer saturation occurs at a lower voltage value when the frequency of the ac…

A:

Q: 55 V / 220 V, 50 Hz single phase transformer, high voltage (secondary) windings are left idle and…

A: Referring the resistance at primary side, R1=0.026  Ωand the inductance at secondary side,X1=0.045…

Q: answer

A: According to question: A) The no-load current of a transformer changes when voltage greater than the…

Q: Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer.…

A:

Q: The picture shown below is a. Step-Up Transformer b. None of the choices c. Step-Down Transformer

A: In this question , we have to write about given transformer..

Q: 4-If the transformer is loaded by purely capacitive load, what is the expected regulation and…

A: if the transformer is loaded by purely capacitive load what is the expected regulation and…

Q: Transferred surge current method is used to find a. Fault in the transformer insulation b. Fault in…

A: Given  Transferred surge current method

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.