A 100/500 V, 1 KVA, 50 Hz transformer was put through open and short-circuit tests to find its parameters. The test conditions and derived parameters are as follows: internal Open circuit test: The high voltage side terminals were open. The low voltage side was connected to 10020°, 50 Hz supply. The low voltage side current was measured as 50445º mA. Short-circuit test: The high voltage side terminals were short-circuited. The low voltage side was connected to a variable voltage supply (50 Hz). A full load current of 102-30° A was achieved when the variable voltage supply was at 840° V. The transformer was then put to operation by connecting a load of 400430° N to the high voltage side (secondary) while applying a primary voltage of 10020° V. Calculate the primary current (the current drawn from the power supply).

A 100/500 V, 1 KVA, 50 Hz transformer was put through open and short-circuit tests to find its parameters. The test conditions and derived parameters are as follows: internal Open circuit test: The high voltage side terminals were open. The low voltage side was connected to 10020°, 50 Hz supply. The low voltage side current was measured as 50445º mA. Short-circuit test: The high voltage side terminals were short-circuited. The low voltage side was connected to a variable voltage supply (50 Hz). A full load current of 102-30° A was achieved when the variable voltage supply was at 840° V. The transformer was then put to operation by connecting a load of 400430° N to the high voltage side (secondary) while applying a primary voltage of 10020° V. Calculate the primary current (the current drawn from the power supply).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 1N4728 zener diode has a Zz of 10 ohms. Considering the data from the manufacturer's sheet, Vz = 3.3 V with a test current, Iz, of 76 mA. What is the voltage across the zener terminals when the current is 95 mA? When the current is 55 mA? Include the graph where these values are shown.
Academic Departments ETC - CIMS - Taher Salim Har 1-In your own words, describe the classification of materials according to conductivity, with examples of each type. 2- Plot the VIcharacteristics graph of Zener diode, label all values, [write your answer in a paper and upload it in the answer submission link.) A- I of %23
1. An 7.5 V zener diode (7.5 V at 25 deg C ) has a negative temperature coefficient of 0.01%/ deg C What is the zener voltage at 75 deg C. 2. A certain zener diode has a maximum power rating of 300 mW at 40 deg C and a derating factor of 1.4mW/deg C. Determine the maximum power the zener can dissipate at a temperature of 80 deg C. 3. From the datasheet, a 1N4728A zener diode has a ZZ of 10 Q. The datasheet gives VZ = 3.3 V at a test current, IZ, of 76 mA. What is the voltage across the zener terminals when the current is 90 mA? When the current is 45 mA? %3D
ll SuperNe 4G 3:00 PM C @ 6% Question 9 1 points Save A Power supply circuit is delivering0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to I2-Dc 205A 220V omsh 5OHZ O 001 F O 0 02 F O 00167 F O None of the above
Determine the electric current that flows into the circuit in the Figure below. O a. -1.6A Ob. 1.6A c. 2A Od. 1.5A 20V 10 Ohm wwww 5 Ohm 5 Ohm tv
Compute the Approximate output voltage of a PV cell. a. 0.5V b. 150V c. 15V d. 1.5V
A semiconductor diode having ideal forward and reverse characteristics is used in a half-wave recti- fier circuit supplying a resistive load of 1000 Ω. If the r.m.s. value of the sinusoidal supply voltage is 250 V, determine (i) the r.m.s. diode current
the Electrical conductivity of an alloy containing 10 at % of an alloying element is found to be 25.75 x 103 / (Ω cm) at 350 °C a. Determine the contributions to the total resistivity due to temperature and due to impurities. Given that the impurity resistivity coefficient is 1.857 x 10 -4 (Ω cm) and resistivity of Cu at 25 °C is 1.67 x 10-6 (Ω cm). b. what will be the electrical conductivity if this alloy contained 15at% of teh same alloying element at 180
Apply each of diode approximations given the following parameters: D1: Si, rB = 2 Q, rR = 220 kQ D2: Si, rB = 5 Q, rR = 560 kQ and determine the current flowing through D1, D2 and R2, R3, the voltage across R3. Finalize answers as follows: Ideal approx: Id1= Id2= 12= , 13=_ V3= ; 2nd approx: Id1=_ Id23D 12= 13= V3= : 3rd approx: Id1=_, Id2= 12= 13= V3= R1 2.5 ka D1 D2 R3 10 V 2.5 ka R2 1 ko
Need correct answer with explanation in 30 minutes.
2 points Hall coefficient of a specimen of depend silicon found to be 3.66x10 m/C. The resistivity of the specimen is 8.93×10-³2 m. Find the density of the charge carriers (in electrons/m3) and the mobility in (m/V.s). 1.8e22, 0.04 O 1.8e22, 0.05 O 1.7e22, 0.05 O 1.7e22, 0.04 3 points
When a Ge diode is conducting at a temperature of 25oC, VT = 0.64 V. What is the VT at 120oC?Note:Express your answer in 3 decimal places, no need to include the unit.Example: If your calculated answer is 16.8395mA you should answer 0.017.