11 MWth plant operates at a thermal efficiency of 34%. The waste heat is dumped across acondenser which operates at a shell side pressure of 0.717 psia. For the given information below,determine the condenser tube length.ACoolant Flow Rate4.81 x 108 Ibm/hrCoolant Inlet Temperature60 FNumber of Tubes62,832LatticetriangularPitch1.5 inchTube OD1 inchTube ID0.944 inchTube Thermal Conductivity10 Btu/hr-ft-FCondensing Heat Transfer Coefficient1228 Btu/hr-ft²-F

Given Data Work output of plant is : Wout=34.11 MW Thermal efficiency is : ηth=34 %=0.34 Condenser…

A 3411 MWth plant operates at a thermal efficiency of 34%. The waste heat is dumped across a condenser which operates at a shell side pressure of 0.717 psia. For the given information below, determine the condenser tube length. Coolant Flow Rate 4.81 x 108 Ibm/hr Coolant Inlet Temperature 60 F Number of Tubes 62,832 Lattice triangular Pitch 1.5 inch Tube OD 1 inch

A 3411 MWth plant operates at a thermal efficiency of 34%. The waste heat is dumped across a condenser which operates at a shell side pressure of 0.717 psia. For the given information below, determine the condenser tube length. Coolant Flow Rate 4.81 x 108 Ibm/hr Coolant Inlet Temperature 60 F Number of Tubes 62,832 Lattice triangular Pitch 1.5 inch Tube OD 1 inch

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please, I need to solve the question in less than an hour.
Catalogue data of a water-cooled condenser of a manufacturer gives the following details: Condensing temperature 48.9°C Water inlet temperature 37.8°C Water flow rate 20.694 kg/s Capacity 145 tons Estimate the capacity of this condenser with the same water flow rate but with an inlet temperature of 30°C and a condensation temperature of 42°C. The evaporation temperature may be assumed to be constant at 2.2°C.
10. Recall when you were collecting data for the Entrance Loss experiment, there was a ten second delay before the data was posted in Excel. Why was there a delay, and why was it important? 11. Were your theoretical entrance loss factors, KL, higher or lower than your experimental value? What may be some causes for each entrance type? Concentric Tube Heat Exchanger 12. Why was it difficult to achieve steady-state conditions? 13. List at least two assumptions that are being made in the Heat Exchanger experiment, and explain the reasons why they are approximations. 14. What are thermal and hydrodynamic entrance lengths? Are either (or both) of them an issue for the experiment? Why or why not?
Water from a natural river source at 22°C and a flow rate of 25,000 kg/s is used as the heat sink for a condenser unit at a large manufacturing company. The condenser consist of 20,000 tubes and is used to condense steam to liquid at 50°C. construction and 20mm nominal diameter. The condenser is a one The tubes are of thin wall shell, two-tube-passes heat exchanger. convective heat transfer coefficient of 11,500 W/m².K on the tube outer surface and the water flowing in the tubes is required to remove heat at a rate of 2 x 10° W. Environmental laws require that the effluent from the condensing unit to the river source should be less than 35°C. Using both the e-NTU and LMTD methods, calculate the outlet temperature of the cooling water and the required tube length per pass. The specification is a Use T =27°C; and for flow through the tubes use, Nu, = 0.023 Re Pr°4
ENERGY PLANTS: Given : Turbine entry conditions = 16 MPa and 600 oC(Degrees Celsius) Turbine output=5 MPa Phase state saturated water at the heat exchanger outlet and heat exchanger efficiency 85% Required power for district heating = 1100 kW Turbine power= 5500 kW Question: What is the mass flow rate in the boiler?
Write the Advantages of supercritical boiler and disadvantages of supercritical boiler.
• A 6 MW generator had a thrust of 103,000 lb. The outside diameter of the step bearing is 12 in, and the inside diameter is 8 in. Employ a film thickness of 0.004 in. Use SAE 20 oil at 120 , the specific heat of the oil being 0.6 BTU/lb deg F, and density of 0.307 lb/cu. in Determine: (d) Temperature rise
Please help me .. answer my Question , I don't want to quote or plagiarize, don't use your handwriting just use MS Word . Question (b)
The condenser of a steam power plant has a total surface area of 45m^2 and an overall heat transfer coefficient of 2100Watts/m^2-K. Saturated steam from the turbine enters this condenser at 30C and leaves as saturated liquid at the same temperature. Cooling water enters the condenser at 14C and leaves at 22C. A. Draw the figure, sketch the t-L diagram, then, compute the LMTD of the cross-flow heat exchanger in Kelvin. B. How much heat is transferred by the condenser in MW? C. How much steam passes through the condenser in kg/s? D. How much cooling water is supplied to the condenser in kg/s.
. A 10 TR ammonia ice plant has a two-pass shell-and-tube water-cooled condenser. The water enters at 30°C. The temperature rise of water may be taken as 2.5°C. The refrigerant condensing temperature is 35°C, the heat rejection ratio of the plant is 1.35. The condenser has 24 steel tubes of 21 mm OD and 13.65 mm ID. Determine the length of the tubes.
I need help solving this question.