*It required to design a ducting system to condition the building shown in figure (1). The uantity of outdoor is (20%) of supply air. Using information in table, find 1- The sensible and latent load for cooling coil. 2- The quantity and condition of supply air to each place. 3- By using equal pressure drop method, design the rectangular ducting system with maximum height side (600mm). 4- Illustrate the all process on psychometric chart. Outdoor 45 °C db & 30% RH Out let type Celling

*It required to design a ducting system to condition the building shown in figure (1). The uantity of outdoor is (20%) of supply air. Using information in table, find 1- The sensible and latent load for cooling coil. 2- The quantity and condition of supply air to each place. 3- By using equal pressure drop method, design the rectangular ducting system with maximum height side (600mm). 4- Illustrate the all process on psychometric chart. Outdoor 45 °C db & 30% RH Out let type Celling

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

no typing please handwright
Alert for not submit AI generated answer. I need unique and correct answer. Don't try to copy from anywhere. Do not give answer in image and hand writing
Please dont late give me Last number
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case:
Please find the highest thermal efficiency possible, while remaining within the boundaries. What is required: -Power produced must be at least 60 Mega Watts -Thermal efficiency must be greater than 36% -Back-work ratio must be smaller than 48% Assume: -air is the working fluid -specific heats vary with temperature (use table A-17) -Compressor inlet is at 1atm and 300k -the combustion process is isobaric and is modeled as a heat exchanger -Turbine exhaust is the same pressure as compressor inlet Compressor specifics: -Max volume flow rate (m^3/h) = 600,000 -Max outlet pressure (atm) = 12 -Isentropic efficiency = 90% Combustion chamber and gas tubine specifics (Note these come as a set) -Max pressure = 16.7 atm -Max temp = 1500 (celcius) -Turbine isentropic efficiency = 92% -Max heat rate = 230MW
An air-cooled condenser has an expected U value of 30 based on the air-side area. The m²-k condenser is to transfer 60 kW with an airflow rate of 15 kg/s entering at 35°C. If the condensing temperature is to be 48°C, what is the required air-side area? Recall Cp,air = 1.0- kg-K kJ
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case:
A R22 refrigeration system is used to operate between 45degC and -30degC. The total cooling capacity is 350 kW. a. What is the ideal COP of the system? b. What is the heat rejected by the system? c. What is the total power consumed by the system? There are several steps made to improve the performance of the system. What happens to the COP, heat rejected and power consumed by the system when: d. For the same evaporator and condenser pressure, the temperature at the entrance of the compressor is -20degC, and the inlet to the expansion valve is subcooled by 5degC. Due to the wide temperature gap, it is decided to use a two-stage refrigeration system using flash gas removal and optimal intercooling operation in a flash chamber. What happens to the COP, heat rejected and power consumed by the system when: e. Having a low pressure and high-pressure compression. f. Two evaporators and two compressors, with the lower temperature evaporator having a cooling capacity of 225 kW. Notes: The…
Show complete solution and illustration please.
Space storage food requires system cooling capacity 10 ton refrigeration operates in the evaporator temperature -17.8 °C and temperature condenser 33.9 °C. Refrigerant used is R-717 and system operate on conditions saturated. Specify: a. COP = b. The flow rate of the refrigerant = kg/s. c. The rate of heat loss in condenser = kJ/s.
3. The system in Problem 2 assumes the AT for heat transfer between the refrigeration system condenser and the environment is zero, and the AT between the refrigeration system evaporator and the cold space is zero. This gives us the best possible performance, but it is unrealistic as you need some reasonable AT to drive the heat transfer. Assume you have a Carnot refrigerator that provides the same 10.55 kW of cooling, but the condenser operates at 35°C and the evaporator is at -15°C. These then, respectively, push heat to the environment at 20°C and pull heat out of the 0°C cold space, as shown in the figure. Assuming the cycle itself (i.e., inside the dashed line) still operates as a Carnot refrigerator, find the electric power needed to generate the 3-tons of cooling capacity, the daily cost for this electricity, and COPR. Environment=20°C QH QH Q₁ Q₁ Cold Space=0°C 35°C W -15°C