Problem 3 A shell and tube heat exchanger consists of a one pipe inside another pipe as shown. The liquid flows in opposite directions in each pipe. If the speed of the liquid is the same in each pipe, what is the ratio of the outer pipe diameter to the inner pipe diameter if the discharge in each pipe is the same? Do D

Q: could you pls provide part D and E

A:

Q: a) Calculate the Pitch diameter for the following thread. Given the measurement over the wires is…

A:

Q: The efficiency of a power screw does nột depend on which of the following variables. Hint: Look at…

A: formula for efficiency of power screw is given byη=Fl2πThere F=load in newtonl=lead T=torquetorque…

Q: Ex. #1 central pitch. The dedendum equals 1/P, inch, the clearance is to be one-eight of the…

A:

Q: The figure below shows the components of normal forces, the value of radial force on the gear wheel…

A: Write the given value using suitable variables. Here Ft signifies tangential force, and 0 signifies…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Displacement Volume - Retraction 11 Calculate the volume of the cylinder during retraction.…

A:

Q: Solidworks. Units are IPS. 24 threads per inch. Primarily just need help designing the threads after…

A: It is asked to draw thread by using Solidworks software

Q: Tapered gibs are adjusted by screws spaced out along the length of the gib. Select one: O True O…

A: Tapered gibs

Q: A pneumatic system is producing 50 lb/in.2 of gauge pressure. A cylinder is needed to press an…

A: The force produced by the pneumatic cylinder can be calculated using the formula: Force = Pressure x…

Q: A slip gauge setting height  of 65.215mm is observed and an angle of  480 is found during the…

A: Given data, Slip gauge height  (h) = 65.215 mm Angle (€) = 48° Find  Length of sine bar (L)

Q: Differen bending neaf possible ach t

A: for solution refer below images.

Q: 4 mefeor is aout l a gang and is velocity is 4epined by ve t-5, whare is in seconds. Find fre

A:

Q: Find the depth of thread in mm for an external thread, if the pitch is 5 mm. Depth of thread (in mm)…

A: Given : Pitch (p) = 5mm   To find : Depth of thread (d) =?

Q: 4 Am ob jecet is made p fravel obrerver çees fhat it is fraveluing harizbufally fx= 24t° M/ where…

A:

Q: 3.

A: For solution refer below images.

Q: Is 2.0cm3 of aluminum same as 2.0cm3 of lead

A: According to the given data, the volume of the aluminum object is 2.0 cm³  and the volume of the…

Q: I have a pin with a Diameter of 10.00/9.95. What is the Maximum Bow of this pin?

A: bow in pin:-

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: travelling hoizoniany obenier fees ma where t is in seconds. What s the magnitude and vecE of the…

A:

Q: Please derive the two Diameter Formula for SI Units. See figure. Thank you so much Dear, your work…

A: Solution:

Q: a boe is foaveling parth of How/ong illake par the bus reach la5 on sap a conctant speedf a

A: Given:v=17 m/sS=5 km =5000 m

Q: 3.A ball is torsed at s0 m/s at an k the maximum range of the ball and lhcight if the ball was…

A:

Q: If FB = 830 N, Fc = 450 N, determine the magnitude of the resultant force at A. (Figu Express your…

A: Given FB=830NFC=450N

Q: 7. Pitch 8. Length of threads 11. Pitch 16. Pitch

A: Standard designation for Metric thread

Q: For the following thread designation, turns, how far have you advanced the O 083 inches O 417 inches…

A:

Q: Match M, V, or N to the correct definition could have units kN-m bending moment 1. M perpendicular…

A: In the above question there are three variables M, V, and N. Here, M symbol used to represent the…

Q: Please select all standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in..     7.80…

A: The standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in. are: 7.80 in. 7.95 in.…

Q: Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a =…

A:

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Q: 6-a toy sparechúp is attached by asiring ts a ceiling fan and a the fan atatas the spiceship trauefs…

A:

Q: What is the LMC of shaft C?

A: The Least material condition (LMC) tells about the minimum material can be used to produce the…

Q: Using the Brown & Sharpe dividing head with the above standard gears and the differential indexing…

A: Brown and Sharpe is the name of the scientist who discovered the concept of head indexing. Indexing…

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. A = 3.55 B…

A:

Q: Derive the function for the efficiency of screw gage

A: Given Screw gauge To find Function and formulation of screw gauge

Q: 1. d. . develop an algebraic equation for calculating the outside diameter d, of Using T=- ---), and…

A:

Q: 50 +0.012 mm and the hole size are 1. The dimensions for the shaft size are +0.015 50+0.005 +0.000…

A:

Q: An cylinder has a volume of 38.5 cu.in. and clearance of 2.5 cu.in. Calculate the stroke, if the…

A: Given data:

Q: Add the Correct Answer Calculations 1. 1/4 indicates 2. 20 indicates UN is an abbreviation for Shape…

A: Since you have asked multiple sub-parts only the first 3 subparts are solved for you, If you want…