A 25 KVA, 2200/220 V, single phase transformer has rated copper loss of 350 watts. With the low voltage winding shorted, it requires 100 V across the high voltage winding to permit rated current to flow through both windings of the transformer. Determine the percent impedance of the transformer. Your answer

A 25 KVA, 2200/220 V, single phase transformer has rated copper loss of 350 watts. With the low voltage winding shorted, it requires 100 V across the high voltage winding to permit rated current to flow through both windings of the transformer. Determine the percent impedance of the transformer. Your answer

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 11000/230 V, 150-kVA, 1-phase, 50-Hz transformer has core loss of 1.4 kWand full load copper loss of 1.6 kW. Determine (a) the kVA load for max. efficiency and(b) the value of max. efficiency at unity power factor
Q2/ Fill in the blanks: 1- The two windings of a transformer is linked. ***** 2- If a transformer primary is energized from a square wave voltage source, its output voltage will be.......... 3- The primary winding of a 220/6 V, 50 Hz transformer is energized from 110 V, 60 Hz supply. The secondary output voltage will be ...... V.
A single phase 220/6 Volt, 50 Hz transformer has a rated primary current = 0.5 A. its maximum efficiency is at load current = 15 A and equal to 94% at unity p.f. Its efficiency at rated load, 0.65 p.f. lagging is: 087.8%. 092.3%. 090.9%. O None.
B/ Fill in the blanks: 1. The purpose of providing the iron core in the transformer is to 2. A transformer transforms... 3. Power transformers are designed to have maximum efficiency at 4. The transformer ratings are usually expressed in terms of menm
Draw the circuit diagram, which finds the copper loss of the transformer without connecting the load. And Calculate the leakage reactance ( Io). Fast pleasee
Explain this diagram
Core losses of a single phase 440/240 V, 24 kVA, 50 Hz transformer is 750 W. Maximum efficiency of the transformer is 90% at 15 kVA load and a certain power factor. Find the efficiency of the transformer at the same power factor and full load.
Find the elements of the equivalent circuit attributed to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuit are 200 volts and 400 volts, respectively, with a frequency of 50 Hz. The primary no-load current at the voltage of 200 volts is 0.7 amperes and the loss of the core is equal to 70 watts. The resistance and reactance of the primary are 3.2 ohms and 1.25 ohms, respectively. The resistance and reactance of the secondary are 0.6 ohm and 0.07 ohm, respectively. Draw the equivalent circle, showing the values of its elements.
A 36/240 V phase transformer, belonging to a phase measured from the no-load (idle) run and short-circuit test. values are given in the table below. High voltage by applying rated voltage to the low voltage winding (The winding ends were left unloaded and the results of the no-load test results were obtained. By applying nominal current to the high voltage windings, the low voltage windings were short-circuited, and the results of the short circuit test were obtained. In direct current test 1 V direct voltage is applied to the low voltage winding, and the transformer draws 500 A direct current. All equivalent Calculate the circuit elements as moved to the low voltage side. Idle run test: Voltage : 36V Power : 68W Current : 2,8A Short circuit test: Voltage : 15V Power : 325W Current : 42,2A
b) The parameters of the transformer equivalent circuit are given bellow, Primary =1290. Secondary winding turns =130. The resistance of the primary winding =0.2 O. The resistance of the secondary winding =0.06 N. The leakage reactance of the primary winding =1.47 Q. The leakage reactance of the secondary winding =0.07 Q. using the above parameter values, referred to the primary winding, determine (a) Equivalent resistance, (b) Equivalent reactance, (c) Equivalent impedance and (d) The phase angle of the impedance.
2- Proved that a resistance of (R¡ )in primary is equivalent to (R1 K’ )in secondary.? 3- A 40-kVA, 3,300/240-V, 50 Hz, 1-phase transformer has 660 turns on the primary. Determine (a) the number of turns on the secondary (b) the maximum value of flux in the core (c) the approximate value of primary and secondary full-load currents. Internal drops in the windings are to be ignored.