A 1,400-N uniform boom at ø = 63.5° to the horizontal is supported by a cable at an angle 0 = 26.5° to the horizontal as shown in the figure below. The boom is pivoted at the bottom, and an object of weight w = 2,050 N hangs from its top. Pivot (a) Find the tension in the support cable. 1.41 Your response differs from the correct answer by more than 10%. Double check your calculations. kN (b) Find the components of the reaction force exerted by the pivot on the boom. (Assume the positive x-direction is to the right and the positive y-direction is upward. Include the sign of the value in your answer.) 1.26 horizontal component Your response differs from the correct answer by more than 10%. Double check your calculations. kN vertical component 2.75 kN

A 1,400-N uniform boom at ø = 63.5° to the horizontal is supported by a cable at an angle 0 = 26.5° to the horizontal as shown in the figure below. The boom is pivoted at the bottom, and an object of weight w = 2,050 N hangs from its top. Pivot (a) Find the tension in the support cable. 1.41 Your response differs from the correct answer by more than 10%. Double check your calculations. kN (b) Find the components of the reaction force exerted by the pivot on the boom. (Assume the positive x-direction is to the right and the positive y-direction is upward. Include the sign of the value in your answer.) 1.26 horizontal component Your response differs from the correct answer by more than 10%. Double check your calculations. kN vertical component 2.75 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The two sub questions and question g as well :
Given the problem: The smooth disk shown in the figure is pinned at 'D' and has a weight of 24.6 lb. Neglecting the weights of the other members, determine the following: d.) Horizontal component at 'D' in lb. e.) Vertical component at 'D' in lb. *Round off final answer in 4 decimal places. Thank you.
SITUATION E:A 30 m steel tape weighing 1.45 kg is of standard length under a pull of 5 kg supported for full length. The tape was used in measuring a line 938.55 m long on a smooth level ground under a steady pull of 10 kg. Assuming E= 2x106 kg/cm2 and the unit weight of steel to be 7.9x10-3 kg/cm³. Determine the total correction for increase in tension -0.068 m +0.068 m -0.038 m +0.038 m
The hoisting arrangement for lifting a large pipe is shown in the figure SD-05Q002. The spreader is a steel tubular section with outer diameter 75 mm and inner diameter 60 mm. Its length is 2.5 m and its modulus of elasticity is 200 GPa. What is the maximum weight of pipe, in kN, that can be lifted based on the following conditions? (Assume pinned conditions at the ends of the spreader.) Use: V = 3 H = 4 Problem 7 Based upon a factor of safety of 2.0 with respect to Euler buckling of the spreader. a. 205 b. 434 c. 355 d. 217 Problem 8 Based upon the allowable stress design if Fy = 248 MPa. a. 205 b. 434 c. 355 d. 217 Problem 9 Based upon the critical stress. a. 205 b. 434 c. 355 d. 217
A cantilever beam, 3.5 m long, carries a concentrated load, P. at mid-length. Given: P = 200 KN Beam Modulus of Elasticity, E = 200 GPa Beam Moment of Inertia, I = 60.8 x 10 mm 1.75m ť How much is the deflection (mm) at mid-length? Select the correct response 100 1.84 29.4 23.5 1.75m
H.W. A circular bar having 200 mm? area is subjected to axial loads as shown in Fig. Find the value of (P) and the total elongation. Take E=2*105 N/mm?. B 50KN P 10kN 50KN 1M 1 M 1 M
THUMBS UP WILL BE GIVEN. WRITE THE COMPLETE SOLUTIONS. BOXTHE FINAL ANSWER. SOLVE IN 2 DECIMAL PLACES.
Schematic diagram of a one degree of freedom bridge that can be opened and closed as follows.shown. The weight of the bridge is given as = −??⃗. Using the Virtuel (Virtual) Works method,Find the value of the counterweight Q so that the bridge can stabilize at a given position with the angle. ?⃗⃗⃗ =−??⃗ ‘dir. Also, state the effect of the value of on the equilibrium condition.
Mechanics of deformable bodies. Two decimal places.
2. Please solve the problem step by step and explain. Thank you.
If beam as shown in Figure has a rectangular section with a depth of 100mm and width of 20mm, calculate the slope and deflection at free end. Assume E = 200GPa. where P= 25