As shown, a uniform beam of length d = 1.80m and mass 21.3kg is attached to a wall with a pin at point B. A cable attached

Q: Problem 105 A homogeneous 800 kg bar AB is supported at either end by a cable as shown in Fig.…

A: Given : Weight of bar AB = 800 kg Allowable stress = 90 MPa in bronze Allowable stress = 120 MPa in…

Q: An 9m long steel column is pinned at the top and fixed at the bottom. The column is provided with…

A:

Q: iven data: L1= 490mm L2=420

A: Draw the diagram From the above diagram sinθ=0.765, Cosθ=0.656Sinα=0.677, cosα=0.830 Calculate the…

Q: A wooden bar beam arrangement is shown in the figure. The beam is formed by nailing wooden bar and…

A: Given,B = 200 mm H = 360 mm t = 20 mm F = 250 NV = 3.2 kN or 3200 N

Q: Q3: A homogeneous 1200 kg bar AB is supported at either end by a cable as shown in Fig.3. Calculate…

A:

Q: Question 1 For the structure shown in Figure Q.1: (a) Calculate the magnitude of force G, given that…

A: S

Q: MY QUESTION IS WHY IS IT 4 ON THE UNDERLINED ONE?? I DON'T UNDERSTAND

A: Since the perpendicular distance of RBH  and RBV  from point A is 1.2 m each, hence moment about A…

Q: . As shown in the following figure, once the compressive force of Pb is applied to the pole of the…

A: Given,  L = 8 m Diameter = 3.2 cm E = 21x 10^5 kg /cm²

Q: Figure 1 shows a rigid body supported by a truss system, all elements are pinned at both ends. If a…

A:

Q: Figure Q2 shows a simply supported beam carrying two point loads. The beam has the cross-section…

A: Figure is as shown

Q: what is the largest allowable intensity wo of

A:

Q: 1. 30 kN 90 cm 555 cm - 27 kN Elastisite modülü 207 GPa olan ve silindir şeklindeki iki çubuktan 1…

A:

Q: 3. 4) For the truss structure below, if the maximum force that any member can support is 19 kN in…

A: To determine the maximum value of force P that can be supported considering the allowable member…

Q: A steel rod having a cross-sectional area of 332 mm^2 and a length of 176 m is suspended vertically…

A:

Q: L M K 100 kg

A:

Q: As shown on the figure is a bar supported by two cables. If the bar has a mass of FN kilograms and…

A:

Q: (a) Calculate the magnitude of force G. given that the maximum normal stress in each member should…

A:

Q: Problem 6.41 Consider the truss shown in (Figure 1). Suppose that F = 25 KN Part A Determine the…

A: Given ; F = 25 kN To Find :: 1) FFE 2) FEB 3) FBC

Q: A simply supported beam of span 4 m carries a concentrated load P acting downward at distance 1.5 m…

A:

Q: Two wires support a weight W. The stresses in the wires AB and AC are not to exceed 81 MPa and 161…

A:

Q: For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural shearing…

A:

Q: 10 mm L2 = 460 mm L3 = 690 m

A: Draw the free body diagram From the above diagram sin θ=0.75, cos θ=0.67sin α=0.411, cos α=0.9123…

Q: The simply supported beam is subjected to the loadings shown in Figure Q2. Determine the value of P…

A:

Q: A 2D structure having members connected by smooth pins is subjected to a load of 20 kN as shown in…

A: Given data, A 2D structure having members connected by smooth pins is subjected to a load of 20 kN…

Q: Q/Find the maximum tensile and compressive flexure stresses for the cantilever beam shown in Fig. *

A: Given- C=130mmL=6mI=100×106

Q: etermine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P…

A: