A 1200 kVA, 3.3-kV, three-phase, star-connected alternator has an effective resistance that is 1.5 times the dc resistance. The dc resistance is obtained by connecting two terminals to a dc source. The current and voltage are 87.6 A. and 6V, respectively. A field current of 30 A produces a current of 200 A on short-circuit and 1.1 kV on open circuit. a. Calculate the power angle and the total generated complex power when the generator is operating full-load of 1200 kVA at 0.9 pf lagging and at rated terminal voltage. Assume that flux varies as the field current. b. If the altenator is operating at the same excitation voltage as in (a), calculate the maximum kW output of the alternator.

A 1200 kVA, 3.3-kV, three-phase, star-connected alternator has an effective resistance that is 1.5 times the dc resistance. The dc resistance is obtained by connecting two terminals to a dc source. The current and voltage are 87.6 A. and 6V, respectively. A field current of 30 A produces a current of 200 A on short-circuit and 1.1 kV on open circuit. a. Calculate the power angle and the total generated complex power when the generator is operating full-load of 1200 kVA at 0.9 pf lagging and at rated terminal voltage. Assume that flux varies as the field current. b. If the altenator is operating at the same excitation voltage as in (a), calculate the maximum kW output of the alternator.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.8MCQ: An ac resistance is higher than a dc resistance. True False

See similar textbooks

Similar questions

helpp
Q5: A 3-phase, 50 Hz, 8-pole alternator has a star-connected winding with 120 slots and 8 conductors per slot.The flux per pole is 0.05 Wb, sinusoidally distributed. Determine the phase and line voltages.
10. A potential difference of 250 V is applied to a field winding at 15-C and the current is 5 A. What will be the temperature of the winding when current has fallen to 3.91 A applied voltage being constant. Assume temperature coefficient at 15'C is equal to 1/254.5 per °C
Full solutions for the question with explanation
The voltage regulation of an alternator having 0.75 leading p.f. load, no-load induced e.m.f. of 2400V and rated terminal voltage of 3000V is............... percent. *
The dc armature resistance of delta-connected alternator measured across its two terminal is 0.8 ohm. The effective resistance per phase is?
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
Indicate the equation that allows determining the voltage generated per phase, in a three-phase alternator supplying any type of load.
An alternator requires an alternating current of 2.1A to produce on short circuit its full-load current of 50A. The same excitation produces on open-circuit an emf of 320V. The armature resistance is 1Ω. Find the full-load percentage regulation with a lagging pf of 0.6 when terminal pd on load is 2000V. a. 7.2%b. 28.8%c. 3.6%d. 14.4%
a) A sinewave is having a frequency of 100 Hz and instantaneous value of 150 Volts at 1.4 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 1.8 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and o =30 degrees. Vp t= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.8 ms b) Angular frequency =
I need the answer at 20 minute
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.