strength of materials 9.) Determine the width w of the plate loaded as shown if the permissible stress in plates of joints through the pin is 200MPa10.) Design the above joint using the welded connection. The required length of the weld is: Qui: XE ROX XE ENC XO Just Xy! ACL XΣ Con xA (DO Xy! Con XEng x3 Eco Xf (2) F ×ь Му х+->A classroom.google.com/u/1/c/MzgxNjM2NzEOMzYx/a/NDE1NDE2MTM×NJEO/detailsRE AppsM GmailYouTubeМаpsTranslateSolution_Manual-_E..3 Thermodynamics 1.3 Pipe | Steam Engine...3 Engineering Materi.E Reading listCSR>Answer: Max. Moment =STRENGTH OF MATERIARIBSABE 3-2_TTH_8:30-10_ROOM10KNw = 5 kN/mM=25 kNmBO Quiz 51m1m1mAssignedDelaCruz RoySeard100 points8. A truck and trailer combination rolls across a 44 ft span. The axle loads of the truck are P1=NNE CINEN..4000# & P2 =8000# with a wheel base of 9 ft. The trailer has an axle load of P3 = 6000 # with adistance of 8 ft from rear wheel load of the truck. Under which wheel load is momentSolve the followingmaximum? Answer:PinAdd or create9. Determine the width w of the plate loaded as shown if the2000 N10 mm 6permissible stress in plates of joints through the pin is 200MPa.2000 NTurn inAnswer:2 mmProblem 110. Design the above joint using welded connection. The required2 mmlength of weld is:Answer:nmentshent to DelaCruzProblem 2earcaJoseFacebookfYou have new notifications.Problem 3Google Chrome • www.facebook.com9:10 PMENG24/10/202122

Answered: Image /qna-images/answer/1f791152-8d98-47e0-ab68-026359bcc1fa.jpg

9. Determine the width w of the plate loaded as shown if the 2000 N 10 mm permissible stress in plates of joints through the pin is 200MP.. 2000 N Answer: 10. Design the above joint using welded connection. The required 2 mm length of weld is: Answer:

9. Determine the width w of the plate loaded as shown if the 2000 N 10 mm permissible stress in plates of joints through the pin is 200MP.. 2000 N Answer: 10. Design the above joint using welded connection. The required 2 mm length of weld is: Answer:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tensile load of 330,000 N is applied to a copper pipe with maximum allowable stress of 110 MPa and 80 mm inner diameter. What should be the thickness of the pipe? Choices: A. 9.78 mm B. 12.35 mm C. 11.56 mm D. 10.55 mm
2. A G10200 HR steel bar of thickness h is welded to a vertical support of the same material as shown below. If an E6010 electrode is used, determine the maximum force F that can be applied while satisfying welding code. The dimensions are h=5 mm, b = 50 mm, and d = 50 mm. HINT: you will need to check failure of the weld material and base materials. d b h F
i need the answer quickly
A 50 mm diameler solid shaft is welded lo a flat plate by 10mm fille: we d The maximum lorque that the welded joint can Sustain if the maximum shear stress intensity in the weld malerial is not to exceed 80 N/mm?, will be
A 50 inches diameter storage tank is used to store air at an internal pressure of 625 psi with a FS = 4.5 based on ultimate strength. If the welded joints have a joint strength efficiency of 80% and the steel used to create the tank hasan equivalent strength similar to C1118,a. find a suitable plate thickness of the tank. Compare the stresses for both diametral section and longitudinal sectionb. Using the thickness solved in (a), determine the pressure to cause actual failure to the vessel
QUESTION 2 1.2 A thin cylindrical pressure vessel has the following specifications Internal pressure 5.33 MPa Metal thickness 20 mm Maximum allowable stress 120 MPa Efficiency of the longitudinal joint Efficiency of the circumferential joint 80 % 50 % 1.21 Determine the maximum internal diameter which the cylinder may have. 1.2.2 The actual values of the hoop and longitudinal stresses. For the soolbar, press ALT=P10 (PC) or ALT-FN-F10 (Mac). B IUS Paragraph Ara !! 140x AITZAN LAINA