Answered: Q2: The plate shown is welded to the…

Q2: The plate shown is welded to the support by using fillet .If the maximum shear stress does not exceed 25 MPa find the size of the weld (h). Top view 40 mm 120 mm 2 kN Front view

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need a solution within 15 minutes
A shaft with two diameters connected by a fillet is shown below. In the diagram, di - 45 mm, d2- 50 mm, and the fillet weld has a radius of 7.2 mm. If the shaft is used to transmit 2400 W at 250 rpm, what is the maximum shear stress in the shaft? d2 d1
ttempt.php?attempt=1404248&page=D13 A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.7 MPa in the x-direction and a tensile stress of 17 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. Wek Lütfen birini seçin: a. 13.992 MPa/7.08 MPa b. 0.3076 MPa/4.38 MPa c. None d. 0.3076 MPa/7.08 MPa e. 12.923 MPa/6.91 MPa DIN PriSc Insert F FIZ
wall thickness=0.23 in. allowable normal stress B=56⁰ inside diameter = 66 in. perpendicular to the weld = 10.1 ksi allowable shear stress parallel to the weld =4.4 ksi What is the largest gage pressure inside the tank? Answer in psi rounded-off to 1 decimal place y X
i need the answer quickly
QUESTION 3 2. For the given welded bracket shown, design the required size of weld needed to resist the given eccentric load P=125 kN. Use E70xx electrode. Where: X=150mm, Y=125mm, Z=50mm what is the maximum force on the welds in kN? (2 decimal places) X Y
Hi please help
(1) What are the methods used to obtain a good weld when welding steel when the carbon content is high? b) Find the appropriate size and length for the weld joint shown in the figure if the strength is equal to (70000Ib) and the allowable shear stress value is 40ksi and the weld rib dimension is (1/4in)
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 500 mm and a wall thickness of 6 mm. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 25 MPa. 50 O 2.63 MPa О 3.13 МРа О 3.36 МРа O 2.88 MPa O 2.44 MPa
This is my Question... Determine the vertical displacement of joint C . EA is constant Determine the Vertical Displacement of the Joint C. EA is Constant Thank You Very Much
i need help solving this question, all parts need to be solved
a. figure 1 shows a large pressure vessel fabricated by welding together steel plates of 12 mm thickness as shown. If the stress acting normal to the welds must be less than 80 MPa, what is the largest allowable internal pressure? b. determine the state of strain in the tank when the internal pressure is 0.3 MPa. The elastic modulus (?) of the steel is 200 GPa, and the Poisson’s ratio (?) is 0.3. c. The welded joints are to be replaced with equally spaced rivets (loaded in single shear), each with a diameter of 10 mm and maximum allowable stress of 80 MPa. For an internal pressure of 0.3 MPa inside the tank, determine: (i) The minimum rivet spacing (?) along the circumference of the tank. (ii) The minimum rivet spacing (?) along the height of the tank. d. If the pressure vessel is subjected to a temperature change of 50°C determine the change in height. The co-efficient of thermal expansion for steel can be taken as ? = 11.2 × 10−6 °C−1.