Q1. A bracket is to be welded as shown in Fig. if the size of weld s mm, allowable shear stress is not to exceed 80 MPa. Determine the load P which can be carried. b b a mm mm mm mm 88 | 108 54 13 All Dimension in mm

Q: Water flowing in a horizontal pipe is at a pressure of 1.40 x 10^5 Pa at a point where its cross…

A:

Q: In the figure shown, Given: UB =1.3 m/s 0 = 60° %3D Solve for: a) velocity of A (m/s) b) angular…

A:

Q: b. Number of Links: L= Number of joints: J₁= Number of half Joints: J₂= Mobility = c. Number of…

A: In these drawn mechanism, we need to find the number of lower pairs (binary joints) and higher…

Q: Using the image on the Moment of Inertia Tab, where the following criteria are considered: Assign…

A: The moment of inertia tab is given. The torque applied is given as, T=2 N-m

Q: Create a slider crank mechanism to cut fruit as shown in Fig. 1. Identify all the dimensions…

A:

Q: , how do you add vectors using parallelogram method graphically

A: Vector can be a quantity that has some magnitude and have a specific direction. displacement,…

Q: rs in an ass

A:

Q: A torque of 18 N m is applied to a rotating part. The part has a moment of inertia of 0.078 kgm2.…

A: Here we will use the the torque equation and the rotational motion equation.

Q: please solve the  equations in steps ()i and ()ii

A:

Q: 16. The forces 8,4/3 ,6v3 and a point, the measure of the ang first force and the second force the…

A: Given F1=8NF2=43N=6.92 NF3=63N=10.39NF4=14N To find Magnitude of Resultant

Q: QI: The cutter bar of a mower is connected to the P.T.O. of a tractor making 1500 strokesDer Minute.…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: An object is made from a uniform piece of sheet metal. The object has dimensions of a = 1.35 ft b =…

A: Given data: Dimensions of object:                           a=1.35 ftb=3.55 ftc=2.15 ft Diameter of…

Q: 6. Consider the gear system given below where b is the gap between width of the teeth and empty…

A: Concept: 1) Given gears system is simple Spur Gear Train.  2) Driving gear rotates with required…

Q: 2) As the foot contacts the ground, a ground reaction force of 200 Nat 55* relative to the…

A:

Q: Apply Mason Rule (S&P) to block diegron below. кле (бар) то e(s) Git H₂P G Hs H₂ ((s) H₁ 62 H₁ бу…

A:

Q: What is the radix component for the integer -35

A: This is a really useful lesson that starts with a standard programming language environment for…

Q: use matrix to find solution for omega 3. find vD not in i+j form please.

A: PROBLEM has been solved and student has sought for matrix notation and magnitude wise solution of…

Q: Please write a matlab code to Solve this

A:

Q: Problem: 1 The slider-crank shown in the figure is drawn to a certain scale. If actual length of…

A:

Q: How did you calculate the 233.33 on the second part for the height from the end of the rod DE to the…

A:

Q: solve using analytical way Given a single disk system that rotates as in picture. If: m₁ = 10 kg; R₁…

A: co-ordinates are converted into x-y form. center of mass is found in x-y form and from there…

Q: Questions: 4. Determine an equation that would model the foot’s position when the cyclist is…

A:

Q: Consider a four bar linkage with the following links: L0 = 180mm, L1 = 40mm, L2 = 170 mm. Using…

A:

Q: Determine the following for point C on the slide if the angle theta measures 45 degrees and the BC…

A:

Q: The elevation and tilt angle of table AB are controlled by an operator's hand at point D. The table…

A: Freebody diagram of Table AB:Freebody diagram of the member DCB:

Q: For the quick-return mechanism shown below, the rod DC rotates with a constant angular velocity of 1…

A: For the solution refer below images.

Q: Need correctly.

A: Piston raises pin B, vertically and at a constant rate.

Q: Determine the following based on the given illustration: c) The Moment of Inertia about the X and Y…

A:

Q: Write a MATLAB program that finds the sum for-25 to 5. (Increment by 5). By using (while „loop)

A:

Q: Find the summation of all positive numbers less than 50 which are divisible on 3 or 7. Taina D

A: 3 or 7 which is divisible less than 50. we can say that

Q: Given: A = 10N,+ x - axis B= 20N,+y-axis € = 30N, 30° below + x -axis D = 40N, 50° below - x - axis…

A: To find

Q: Q5:B: Draw the following types of motion: linear deformation, angular deformation and rotation.

A:

Q: Find the oxthagonal r-6a.Cose whese a is pasametes

A: r=6acosθWhere a is a parameter Now need to calculate orthogonal trajectory

Q: show that the cylindrical co-ordinate are generalized co-ordinates.

A: Generalized co-ordinates The term coordinate generalized refers to variables that characterize the…

Q: Problem 16.104 - Rolling without slipping: DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE:…

A:

Q: The punching machine is using the flywheel for its smooth running operation. The flywheel running at…

A: Given data: Convert the “rps” into “rpm” as follows:

Q: Please calculate the moment of inertia values for each figures according to defined rotation axises.

A: Given Data: The radius of the sphere is R. The length of the rod is L. The masses of the sphere and…

Q: The force vs. elongation relationship for a given body is dependent on the body's geometry as well…

A: YES its true.

Q: A particle is moving along a straight line such that its position from a fixed point is s = (12 -…

A: Write the equation for the position of the particle. s=12-15t2+5t3 m Here, s is the position of the…

Introduction to Engineering Design Process

The engineering design process is a set of steps that engineers follow to come up with a solution to a particular problem. The solution to the problem involves the designing of a product that can accomplish a certain task and can qualify certain criteria. The process of designing is completely different from that of the scientific method, that you may be familiar with. If the project utilizes the observations, and the experiments then the engineering design process must be followed. The diagram shows the steps of the engineering design process, and the table below describes each step in more detail: