Answered: Determine the net area along route…

Determine the net area along route ABCDEF for the C380 x 50 (A, = 6430 mm) shown in the figure below. Holes are for 20 mm bolts.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Select a W section bolted as shown in Figure 6.12 with %-in.-diameter bolts, and three bolts per…

Q: The plate shown is 8 in wide and 1/2 in thick. The bolts are 7/8 in. The smallest net area (An) of…

A: Given:- width of plate =8 inthickness of plate =1/2 inBolts diameter size = 7/8 inA36 plateTo…

Q: The group of four bolts shown below is subjected to factored loads Pux-100 kip, Puy=75 kip. The…

A: We need to calculate shear and tension strength of bolts for bearing type connection Calculate Shear…

Q: Determine the design strength of a single C15x50 fastened to a 3/4" gusset plate. Use A36 steel.…

Q: 4. Determine the minimum net area of the angle section having a bolt hole with a clearance of 4mm.…

Q: lines of M20 bolts shown in the figure, determine the pitch (s) in mm that will give it a net area…

Q: Determine the net tensile area for the connection plate shown. Use a 3/8" plate with 3/4" bolts with…

A: Given data, Plate thickness (t)= (3/8) = inches Bolt dia = (3/4) inches So, hole diameter= dh =…

Q: A double-angle shape is shown in Figure 3.5. The steel is A36, and the holes are for…

A: Double angle section is shown in the figure above. Grade A36 steel is used. Diameter of bolts= 1/2…

Q: The tension member shown contains holes for M22 bolts. At what spacing (mm), s, will the net area…

Q: The tension member shown in the figure contains holes for 3/4-in Ø bolts. At what spacing, s, will…

Q: Q17 An L4x4x7/16 tension member is connected with %"Ø bolts, as shown in the figure below. Both legs…

A: Given Data: The size of the tension member is L4×4×716. The diameter of the bolt is 34". To…

Q: Angle Bolted Connection. The L6 x 31/2 × 5/16. -in angles, shown in Figure, The bolts are 3/4 inch…

Q: The 3/4 in x 15 in plate has staggered holes as shown. The holes are for 7/8 in F bolts. Determine…

A: In the case of staggered bolts, Anet=b×t-nd't+ (s12/4g1)+(s22/4g2)where, b= width of…

Q: Compute the allowable tensile strength of the bolted connection shown. Include the allowable block…

A: The angle is made of A36 steel and the bolts are 3/4 inAll parameter is given belowNeed to findTo…

Q: For the connection shown in the accompanying illustration, Pu = 475 k and Pa = 320 k, determine the…

A: LRFD: Load and Resistance Factor Design is used for designing steel structures and structural…

Q: Find the ava shown in the liameter bolts Use LRFI Use ASD 1 2) 3½" I

Q: W 10x45 is connected to two plates with two lines of ¾” bolts as shown below. Determine the tensile…

Q: 1½" 3"<3"→ -1½" 2" С7x 12.2 O O 2" t = ½"

A: Calculation Gross-section nominal strength; Pn = FyAg=50×(3.6)=180 kips Calculation of Net section…

Q: Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The…

A: We know that Maximum factored LRFD tensile force capacity of the member is given by minimum of the…

Q: 2. Compute for the net area of the shape shown. (Note: Bolts are going through different portions of…

A: The section is provided above. It is w 10x19 section. Also 2 M20 bolts are provided in top and…

Q: Calculate the critical net area (mm²) for the tension member shown. The bolts are M22. 40 65 90 115…

A: Given A tension member Required Net area

Q: What is the required bolt diameter at B in mm? * 8.94 10.45 6.32 5.22 13.66 Compute the reaction at…

Q: 9.4 An L 8 x 4 x ½ has staggered holes for %-in. diameter bolts, as shown in Figure P9.4. Determine…

Q: Hhello, Thanks a lot for your help, please I have the following points: 1-Is it allowed to use…

A: Design of tension member

Q: Determine the critical net width for the staggered bolted connection as shown in the figure below.…

A: We will use formula of net width along section A B C D E .

Q: Problem 3.. for 7/8 in bolts. . Compute the net area for the 7/8 x 12 plate shown below. The holes…

Q: Determine the net area of the given section below. Diameter of bolts is 7/8-in and the thickness of…

Q: A 620×230 UB 125 tension member of S355 steel is connected through both flanges by 30 mm bolts (in…

A: Properties of 620x230 UB 125 w = Weight of beam = 125 kgD = Total depth of beam = 620 mmbf = Width…

Q: Solve: Select the lightest 28 ft long W12 available to support a factored tensile load of Pu = 400…

A: The objective of the question is to select the lightest W12 beam that can support a factored tensile…

Q: a. reduction factor U for area b. effective net area FIGURE 3.12 L6 x 6 x ½ 1.67" %-in. bolts 3"3"…

A: Given:- The diameter of the bolts = 5/8 in The tension member used = L6×6×1/2 To determine:- a)…

Q: The tension member shown below is a C 310 x 30.8 of A572M gr 345 steel materials. Will it safely…

Q: The L7 x 4 x 1/2 single angle has two lines of bolts in the long leg as shown (See Figure). The U…

A: The distance from the centroid of the connected area to the plane of the connection, x=0.910 in The…

Q: The plate splice shown in the figure below has 9 – 3/4 inch diameter A325-N type bolts (Group A, N…

A: A325 N type of bolts, N indicates threaded portion will be in the shear plane. Dia of bolt = 3/4 in…

Q: etermine the net area An of a 1/4 in by 4 inches plate and the diameter of the bolt is 7/8 in.…

A: width of plate=4in thickness of plate=1/4in diameter of bolt=7/8 in to find net area of plate

Q: Compute A,, and A, for a 14-in.-wide and ½-in.-thick plate subject to tensile loading with staggered…

A: Given : Width = 14 inches Thickness = 1/2 inches Compute An and Ae for the given plate ?

Q: 17. Determine the net width for a 10×1/2 in. plate with 3/4 in. bolts placed in three lines as shown…

Q: Find the available strength of the S-shape shown in Figure 3.20. The holes are for 3/4-inch-diameter…

A: Given : The S shape is shown below : Dia of holes = 3/4 in. Using A36 steel FInd - The Available…

Q: The L6 x 4 x 1/2 single angle shown has two rows of bolts. Each leg has one row (one line) of 5/8 in…

A: Answer (B) Net area refers to the gross section area minus any holes, notches or other…

Q: Determine the effective net area of the tension member shown in the figure. 000 3"3" L6 x 6 x ½…

A: Given Data- Diameter of Bolt = 3/8 in Find - Calculate the effective net area of the member ?

Q: For the bolted tension member is shown in the figure. Determine the effective area,

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: 1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threads…

A: The width of the plate is B=12 in. The thickness of the plate is t=58 in. The diameter of the bolt…

Q: A 3/4" x 10" X 5' long plate is fabricated from A36 steel and has standard holes for 3/4" bolts at…

Q: The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi. Fu = 58…

Q: Problem 3.. for 7/8 in bolts. . Compute the net area for the 7/8 x 12 plate shown below. The holes…

Question

9. Determine the net area along route ABCDEF for the C380 x 50 (A, = 6430 mm)
shown in the figure below. Holes are for 20 mm bolts.
36.4 mm
50mm
16.5 m
10.2 mm
C380 x 50
B
Igaje
36.4 mm
-
(a)
75 mm
230 mm
75 mm
50 mm
BQ
(b)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt hole is 1/16 inch larger than bolt diameter. Plate 1/2" x 11" .T 7/8" dia. bolt, typ. ASTM A325N
A double cover butt joint is shown in figure 2 below. If the steel is Grade S355JR and the bolts are M20 Grade 8.8 S, determine the strength of the connection. Assume the contact surface of the bolts are blast – cleaned with Class B coatings. The connection is required not to slip at serviceability. 80 120 80 80 120 80 -13 All dimensions are in mm Figure 2: Double cover butt joint. 300 O O O O o o O o o
A double lap splice connection shown in figure B is made up of 6mm x 150mm and 9mm x 150mm. Use NSCP specifications and assume a double row of bolts with standardsize holes for a bearing type connection with threads excluded from the shear planes.Minimum tensile strength Fu = 552.93MPa. Assume diameter hole is 3mm bigger than thediameter of bolts. Allowable shear stress is Fv = 207MPa. Allowable bearing stress fb = 1.2Fu.Diameter of bolts is 19mm. Fy = 449.25MPa.(a) Compute the tensile capacity of the steel plates. (Max. Net Area = 0.85 of Gross Area)(b) Compute the number of 19mm diameter bolts to develop the full strength of the plates. Note: SHOW DRAWINGS AND SOLUTIONS.
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
How many M24 bolts Grade 8.8 will be needed in a tension splice connected to a 20 mm cover plates on the longer leg of a 200 x 100 x 15mm angle in S355 steel, if the full strength of the angle is to be developed?
An L 175 x 175 x 20 is used a tension member, with one gage line of 22 mm bolts in each leg at the usual gage location (where g=100 mm). What is the minimum amount of stagger, "s", necessary so that only one bolt need be subtracted from the gross area of the angle? (Key Answer: 134.20 mm)
Determine the effective net area of a W 360 x 91 shown. The holes were punched for M20 bolts. 65 mm 0000 P O O DO 65 mm 60 85 85 85 mm mm mm mm
1. An L 178 x 102 x 19 with one line of 20mm diameter bolts in each leg in usual gage as shown. Assume the connection length is 450mm. The pitch distance for the subsequent standard size holes is 75mm. Use ASTM A572M Grade 345 steel materials and : a. Determine the design strength of the member. b. Specify the maximum permitted length of the member as per AISC specifications.) 102mm g g 19mm 178mm L 178 x 102 x 19 Gusset Plate
In mm) Problem 8: A C310 × 45 is connected with 25mm diameter bolts in each flange, as shown in Figure, Problem 11. If Fy = 345MPA, Fu = 450MPA, and Ae = 0.90An, Apply the following %3D %3D %3D approaches to determine: a. The design strength for LRFD. b. The allowable strength for ASD. Section Figure. Problem 8
The tension member shown in the figure is connected to a gusset plate as shown with 1.210-inch diameter bolts. It is subjected to the dead and live loads as shown. Take Fy = 33.29 ksi and Fu = 52.93 ksi. Assume Ae = An. a) Draw the critical cross-section and show its dimensions using your data. b) Determine whether this member has enough strength using LRFD and the critical ASCE 7 loading combination.
Find the smallest net area for the plate shown below. The holes are for 1 in. diameter bolts.
7. Determine the design tensile strength of the plate (200 x 10 mm) connected to 12 mm thick gusset, using 24 mm bolts as shown below. Use A572M Grade 345 steel materials. 200 40 50 40 30 30 30 30 40