How many M24 bolts Grade 8.8 will be needed in a tension splice connected to a 20 mm cover plates on the longer leg of a 200 x 100 x 15mm angle in S355 steel, if the full strength of the angle is to be developed?

How many M24 bolts Grade 8.8 will be needed in a tension splice connected to a 20 mm cover plates on the longer leg of a 200 x 100 x 15mm angle in S355 steel, if the full strength of the angle is to be developed?

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter28: Structural Components Of Framed Construction

Section: Chapter Questions

Problem 28.34Q

See similar textbooks

Related questions

Q: An ISA 90 x 60 x 8 mm of steel of grade Fe410 is connected to a 12 mm gusset plate and is used as a…

Q: ¿A Tension member has used to resist load of 65 kips, and the shear stress on bolts is 15.9 kips.…

A: If two or more plates are to be joined then the bolts or welding is used. The applied shear stress…

Q: Example 3.9 FIGURE 3.20 Find the available strength of the S-shape shown in Figure 3.20. The holes…

A: Given member: S15×50 Properties of the given section: Flange thickness=0.622 in We need to…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: Given: Diameter of bolt= 1 inch ( Group A ) Diameter of bolt hole= d0 =116+1=1.06 inch Plate…

Q: a) Calculate the factored load applied to the connection shown. b) Calculate the nominal tensile…

A: Given data: Service load, T=620 kN From given service load, 25% is dead load and 75% is live load…

Q: The bolted connection shown in Figures is connected with 3/4-in-diameter bolts in standard holes.…

A: To find = Available tensile strength of plates

Q: steel section. Check web yielding and web crippling if the steel used is ASTM A992, grade 50.

A: Solution: For W18×50, we obtain the following properties from ASTM, Below are the structural steel…

Q: 5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt…

Q: miscellaneous channel MC 300 x 67 is bolted as shown on the figure 2.20 by a 0 mm diam. bolts. A 36…

A: Area of section, Depth, Thickness of web, Flange thickness, Width of flange, To find: (a)…

Q: For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt…

Q: A steel plate is 360 mm wide and 20 mm thick with four bolt holes cut into a plate as shown in…

A: Given Data: steel plate thickness = 20mm steel plate wide = 360mm

Q: O O O O The steel plate below is attached to a strong gusset plate as shown The plate grade of the…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Number of bolts

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Show 5 failures. Show step by step solution. Steel Type: Cross section flat bar PL 12.7 x 165 with an area of 2095.5 mm2 Textbook reference Handbook of steel construction.
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
Please explain
QUESTION 5 3. check the capacity of the shear connection. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi effective bolt hole diameter = bolt hole + 1/16" beam properties: tw=0.295 in. Fexx=70ksi what is the bolts shear capacity in kips? (2 decimal places) 0.5"| 1.5" 1.5" 5/16 _ 4-3/40 A325 SSLT Bolts 5/16
Calculate the allowable (ASD) block shear rupture strength (kN) of a C230x22, attached through the web with six M20 bolts as shown. The yield strength of the steel is 345 MPa and the ultimate tensile strength is 483 MPa. C230x22 64.5 Ο Ο Ο OO 64.5 50 75 75 +
The butt connection shows 8-22 mm diameter bolts spaced as shown below.Use NSCP2001 Steel strength and stresses are: Yield strength, Fy 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt hole diameter = 25 mm Calculate the allowable tensile load, P, under the following conditions: 1Based on the gross area of the plate. 2Based on the net area of the plate. 3Based on block shear strength. 50 100 50 50 100 50 40 80 40 12 mm 16 mm
The L6 x 4 x 1/2single angle shown has one line of 5/8 in bolts in each leg as shown. The bolts are spaced at 4 in in each line as shown (staggered at 2 in with respect to each other). Determine the net area (An)
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
Please help me solve the net area of the member in figure B
What is the working strength of a 2" bolt which is screwed up tightly in a packed joint when the allowable working stress is 12000 psi? (A) 20,120 lbs. B 20,200 lbs. C) 25,347 lbs. D) 20,443 lbs.
Based on block shear strength of the double angle.
Consider the following bolted connection. Slippage is permitted. Member: L6x6x3/4 3/16 “ gusset plate Pu Pu A36 steel 3.5* 1"diameter A325-X bolts 1 1/4" 3 " 3* 1 1/4" Question 3.1: Please, indicate if the combined bolt shear strength is closer to: Question 3.2: Please, indicate if the combined bolt bearing strength is closer to: Question 3.3: Please, indicate if the angle yielding strength is closer to: Question 3.4: Please, indicate if the angle fracture strength is closer to: Question 3.5: Please, indicate if the angle block shear strength is closer to: Question 3.6: Please, indicate if the overall connection strength is closer to: