The L6 x 4 x 1/2 single angle shown has two rows of bolts. Each leg has one row (one line) of 5/8 in D bolts in each leg as shown. The bolts are spaced in the perpendicular direction to the load as shown. Determine the net area (An)

The L6 x 4 x 1/2 single angle shown has two rows of bolts. Each leg has one row (one line) of 5/8 in D bolts in each leg as shown. The bolts are spaced in the perpendicular direction to the load as shown. Determine the net area (An)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Block Shear The tension member is a PL% x 5% of A242 steel. It is connected to a %-in. thick gusset…

A: PL 3/8 x 5 1/2 A242 steel3/8 in. thick gusset plate, also of A242 steel, with 3/4-inch diameter.To…

Q: *A bracket is held in place using a circular pattern of 6 bolts as shown. The circular pattern…

Q: Determine the design strength of a single C15x50 fastened to a 3/4" gusset plate. Use A36 steel.…

Q: B) The tension member shown in Figure is a W 16 × 40, and the steel is A992. The bolts are 3/4-inch…

Q: Determine the controlling (lowest) net area of the member. X = 2.69 Y = (6-2.69)/2 Z=0,7 Y" -X Y" 5…

A: Controlling net area

Q: 4. Determine the minimum net area of the angle section having a bolt hole with a clearance of 4mm.…

Q: Determine the net tensile area for the connection plate shown. Use a 3/8" plate with 3/4" bolts with…

A: Given data, Plate thickness (t)= (3/8) = inches Bolt dia = (3/4) inches So, hole diameter= dh =…

Q: A double-angle shape is shown in Figure 3.5. The steel is A36, and the holes are for…

A: Double angle section is shown in the figure above. Grade A36 steel is used. Diameter of bolts= 1/2…

Q: The truss diagonal member consists of a pair of angles L5x3/₂2x1/2 that are loaded in tension. The…

A: Answer we are given L 5 x 312 x 12 bolt diameter = 7/8 in A 36 steel member we know that the design…

Q: The tension member shown in the figure contains holes for 3/4-in Ø bolts. At what spacing, s, will…

Q: Q17 An L4x4x7/16 tension member is connected with %"Ø bolts, as shown in the figure below. Both legs…

A: Given Data: The size of the tension member is L4×4×716. The diameter of the bolt is 34". To…

Q: Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in…

A: Answer A 325 group bolt 3/4 inch diameter bolt Plate 38 x 7 Plate 516 x 7 A 36 steel Live loadDead…

Q: Angle Bolted Connection. The L6 x 31/2 × 5/16. -in angles, shown in Figure, The bolts are 3/4 inch…

Q: The splice plates shown in Figure 2 are ½-inch-thick. How many 7/8-inch-diameter, Group B bolts are…

A: Nominal bolt area is given by

Q: The design shear strength phi rnv of one A490 X-bolt, 3/4 inch in diameter (Group B, X type) in…

Q: 7. Compute the tensile capacity for the A36 steel plate shown. Bolts are 7/8 in diameter. Neglect…

A: For A36 steelUltimate Tensile Strength, fu = 58,000 psiYield Tensile Strength, fy = 36,300 psiThe…

Q: Determine the forces that are generated in the bolts (The information is given in units of weight)…

Q: Determine the load-carrying capacity of the 2 PL 5/16 x 3 tension member shown based on the limit…

Q: ) Determine the smallest net area of the tension member shown. The holes are for 19 mm Ø bolts at…

Q: 14: In the tension member connected to a gusset plate as shown below. Determine the valu

Q: Compute the net area. The 1 x 10 plate shown in Fig. P3-10.The holes are for 7/8-in Ø bolts.

A: The calculation of the net area An of the plate is given by - An = Bt - nϕht + nss24ghere,B =…

Q: The tension member is a PL.3 x 5% of A242 steel. It is connected to a 3-in. thick gusset plate, also…

A: PL 3/8 x 5 1/2 A242 steel3/8 in. thick gusset plate, also of A242 steel, with 3/4-inch diameter

Q: Compute the net area. The tension member shown in Figure P3-14 contains holes for 1-in Ø bolts.At…

A: Given:- diameter = 1in To find:- net area

Q: Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The…

A: We know that Maximum factored LRFD tensile force capacity of the member is given by minimum of the…

Q: Determine the LRFD design tensile strength of the bolted connection shown. The angles are connected…

A: Given dia of bolt=16 mm fy =250 fx =405 diameter of hole=16+2 =18 mm

Q: Problem 6: Assume that the pieces making up the connection are adequate, and very stiff such that…

A: Service load, T=620 kNFrom the given service load, 25% is dead load and 75% is live loadGiven bolt…

Q: Calculate the critical net area (mm²) for the tension member shown. The bolts are M22. 40 65 90 115…

A: Given A tension member Required Net area

Q: Compute the net area. The 6 x 4 x 1/2 angle shown has one line of 1-in Ø bolts in each leg.The bolts…

A: The given structure has 1 in bolts in each leg. The bolts are 4-in on center in each line and are…

Q: 2. A double-channel shape, 2C10 x 20 steel, Fy = 50 ksi and Fu = 70 ksi, is used for a built-up…

Q: Determine the critical net width for the staggered bolted connection as shown in the figure below.…

A: We will use formula of net width along section A B C D E .

Q: An A992 steel plate (12mm thick, in yellow) is connected to another A992 steel plate (12mm thick, in…

A: Given data Diameter of bolt (d) = 33mm Let's 2mm extra space is provide in hole for easy fitting…

Q: Problem 3.. for 7/8 in bolts. . Compute the net area for the 7/8 x 12 plate shown below. The holes…

Q: Determine the design strength of the connection shown in the Figure below. The bolts are 25 mm…

A: Given Data Diameter of bolt is given as 25 mm Ultimate tensile strength is given as 400 MPa Yield…

Q: Question 3) The tension member shown in Figure 1 contains holes for in. bolts. At what spacing, s,…

A: We need to calculate spacing between two bolts.

Q: The L7 x 4 x 1/2 single angle has two lines of bolts in the long leg as shown (See Figure). The U…

A: The distance from the centroid of the connected area to the plane of the connection, x=0.910 in The…

Q: 3-21./ Determine the effective net area of the L8 X 4 x ½ shown in Fig. P3-21. Assume the holes are…

Q: Problem # 8.0 The tension member shown is a C12 x 20.7 of A572 Grade 50 steel. Will it safely…

A: The channel section used = C12 × 20.7 The steel used = A572 grade 50 steel The magnitude of the…

Q: The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for…

A: Area = Force/ Shear stress

Q: 17. Determine the net width for a 10×1/2 in. plate with 3/4 in. bolts placed in three lines as shown…

Q: 6. Given a sheared flat bar 8" in width, which is to have a double line of 1 3/8" Dia bolts, answer…

A: A sheared flat bar 8" in width, which is to have a double line of 1 3/8" Dia bolts.Need to finda.…

Q: The 7/8 × 14 plate is shown in the figure. The holes are for 7/8-in Ø bolts. Compute the net area of…

A: Given Data:- Thickness of plate=7/8 in Width of plate=14 in Diameter of holes=7/8 in To find:-…

Q: Determine the LRFD design strength and the ASD allowable strength. Neglect block shear. A36 steel…

Q: The 1 × 8 plate is shown in the figure. The holes are for 3/4-in Ø bolts. Compute the net area of…

A: Given that, width of plate, B = 8 in the thickness of the plate, t=1 in diameter of the bolt, d=…

Q: Determine the effective net area of the tension member shown in the figure. 000 3"3" L6 x 6 x ½…

A: Given Data- Diameter of Bolt = 3/8 in Find - Calculate the effective net area of the member ?

Q: 1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threads…

A: The width of the plate is B=12 in. The thickness of the plate is t=58 in. The diameter of the bolt…

Q: Determine the smallest net area of the tension member shown in the figure. The holes are for 3/4-in…

A: here given double angle sec so please keep this in mind for no. of bolt in net area calculations…

Question

B) The L6 x 4 x 1/2 single angle shown has two rows of bolts. Each leg has one row (one
line) of 5/8 in D bolts in each leg as shown. The bolts are spaced in the perpendicular
direction to the load as shown. Determine the net area (An)
2,5
3.5
2.5
15
***
L6x4x1/2
il
5/8 & diameter bolts
Section
#
4
A
16
++
O
O
O
1
O
O
Elevation
*
2.5
V
*
3,5"
(
✓
Pu
2.5"
1.5"

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. Compute the maximum acceptable tensile service load the angle in Problem (1) may carry when connected on both legs. The 4-in leg contains a single gage line of (7)/8 in diam. Bolts, and the 6-in leg contains a double gage line of 7/8 in-diam. Bolts. Assume no stagger of bolts, and that all bolts participate in carrying load.
The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
Problem 3.. for 7/8 in bolts. . Compute the net area for the 7/8 x 12 plate shown below. The holes are 2 in O 3 in 3 in 4 in 3 in 2 in PL 7/8 x 12 12 in-
A double lap splice connection shown in figure B is made up of 6mm x 150mm and 9mm x 150mm. Use NSCP specifications and assume a double row of bolts with standardsize holes for a bearing type connection with threads excluded from the shear planes.Minimum tensile strength Fu = 552.93MPa. Assume diameter hole is 3mm bigger than thediameter of bolts. Allowable shear stress is Fv = 207MPa. Allowable bearing stress fb = 1.2Fu.Diameter of bolts is 19mm. Fy = 449.25MPa.(a) Compute the tensile capacity of the steel plates. (Max. Net Area = 0.85 of Gross Area)(b) Compute the number of 19mm diameter bolts to develop the full strength of the plates. Note: SHOW DRAWINGS AND SOLUTIONS.
Two steel plate tension members have been connected using 0.72 inch diameter bolts arranged in an equally-spaced 9 by 3 rectangular formation. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 51.2 ksi, clear distance for each edge bolt as 0.12 in, and the clear distance for the other bolts as 1.072 in. a)Sketch the connection showing all the details and measurements with units. b)Find the maximum allowable service dead load and live load assuming live load is half as much as dead load. Consider ASD.
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
The tension member shown in Fig. P3-13 contains holes for 3/4-in Ø bolts. At what spacing, s, will the net area for the section through one hole be the same as a rup- ture line passing though two holes? (Ans. 3.24 in) 2글 in' 8 in 3 in 2늘 int
A C15x40 channel section is bolted to a gusset plate is used to resist a tensile loadPu =313 k. The bolts are 3/4 inch  diameter bolts A325 N (Group A, N Type) used insingle shear to resist this load. The bolts are to be symmetric and arranged in 3 rows.1) Determine the number of bolts needed for this connection. Draw a detailshowing how the bolts are arranged and showing spacing and edge distances onthis connection. Assume edge distance Le = 1.75db , use Le to nearest 1/4 in.2) If the connection is to be replaced by a fillet welded connection with transversewelds only along the channel web, determine the required fillet size to thenearest 16th of an inch.
1. An L 178 x 102 x 19 with one line of 20mm diameter bolts in each leg in usual gage as shown. Assume the connection length is 450mm. The pitch distance for the subsequent standard size holes is 75mm. Use ASTM A572M Grade 345 steel materials and : a. Determine the design strength of the member. b. Specify the maximum permitted length of the member as per AISC specifications.) 102mm g g 19mm 178mm L 178 x 102 x 19 Gusset Plate
The tension member shown in the figure is connected to a gusset plate as shown with 1.210-inch diameter bolts. It is subjected to the dead and live loads as shown. Take Fy = 33.29 ksi and Fu = 52.93 ksi. Assume Ae = An. a) Draw the critical cross-section and show its dimensions using your data. b) Determine whether this member has enough strength using LRFD and the critical ASCE 7 loading combination.
1. The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The bolts are 3/4-inch in diameter. a. Draw the different potential failure lines. b. Compute the effective net area. 22" 2½" 2" 4 3" *₁ 3" ✓ 2" 2. A double-channel shape, 2C10 x 20 steel, Fy = 50 ksi and Fu = 70 ksi, is used for a built-up tension member as shown in the figure. The holes are for 12-inch-diameter bolts. PNA a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. YD Shape A 2" 2" -X Area, Depth, d | 3²²-|-1 3²² | 00 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ O O O Web Thickness, tw in. in. O 4" C10-30 x25 x20 5.87 10.0 10 0.379 % x15.3 4.48 10.0 10 0.240 4 4" Table 1-5 C-Shapes Dimensions Flange Width, b₁ 2 in. in. in.2 in. C15x50 14.7 15.0 15 0.716 1168 3.72 3% 0.650 % x40 11.8 15.0 15 0.520 x33.9 10.0 15.0 15 0.400 % 14 3.52 32 0.650 % %/16 3.40 3% 0.650 % C12-30 8.81 12.0 12 0.510 4 3.17 3% x25 7.34 12.0 12…
8. Determine the effective net area of the W 16 x 40 shown. Assume the holes are for ¾ in diameter bolts. W16 X 40 in Ø bolts PA % 12 121 All 3 in