Answered: What is the Nominal Shear Capacity of…

What is the Nominal Shear Capacity of the following shear splice 3/4" A325N bolts W18x35 W24x55 F1 1/2" 1/4" A36 plate on both sides -1 1/2" 1" *5" Kt3 @ 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. check the capacity of the shear connection. A992: Fy=50ksi, Fu=65ksi A36: Fy-36ksi, Fu=58ksi…

A: Given Data: A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole…

Q: 3.5-1 Block Shear The tension member is a PL3 x 5% of A242 steel. It is connected to a 3-in. thick…

A: PL 3/8 x 5 1/2 A242 steelconnected to 3/8 in. thick gusset plate, also of A242 steel, with 3/4-inch…

Q: Determine the design strength of a single C15x50 fastened to a 3/4" gusset plate. Use A36 steel.…

Q: For the splice connection shown in the figure, Compute the design strength based on shear and…

Q: Compute the available block shear of the gusset plate a) Per LRFD b) Per ASD

A: The gusset plate given as belowNeed to findAvailble block shear failure (a) Per LFRD(b) per ASD

Q: Determine the net tensile area for the connection plate shown. Use a 3/8" plate with 3/4" bolts with…

A: Given data, Plate thickness (t)= (3/8) = inches Bolt dia = (3/4) inches So, hole diameter= dh =…

Q: A double-angle shape is shown in Figure 3.5. The steel is A36, and the holes are for…

A: Double angle section is shown in the figure above. Grade A36 steel is used. Diameter of bolts= 1/2…

Q: ¿A Tension member has used to resist load of 65 kips, and the shear stress on bolts is 15.9 kips.…

A: If two or more plates are to be joined then the bolts or welding is used. The applied shear stress…

Q: Example 3.9 FIGURE 3.20 Find the available strength of the S-shape shown in Figure 3.20. The holes…

A: Given member: S15×50 Properties of the given section: Flange thickness=0.622 in We need to…

Q: Q17 An L4x4x7/16 tension member is connected with %"Ø bolts, as shown in the figure below. Both legs…

A: Given Data: The size of the tension member is L4×4×716. The diameter of the bolt is 34". To…

Q: Calculate the shear stress that will need to be developed in the 1 inch diameter bolts, it the…

Q: Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in…

A: Answer A 325 group bolt 3/4 inch diameter bolt Plate 38 x 7 Plate 516 x 7 A 36 steel Live loadDead…

Q: Angle Bolted Connection. The L6 x 31/2 × 5/16. -in angles, shown in Figure, The bolts are 3/4 inch…

Q: The design shear strength phi rnv of one A490 X-bolt, 3/4 inch in diameter (Group B, X type) in…

Q: CLO3: Determine the tensile capacity of the 1/2-in. by 7-in. plate shown in Figure bellow. The…

A: Given: The cross-section of the plate is ½ in x 7 in. The diameter of the bolt is 6/8 in. The value…

Q: The tension member is a PL.3 x 5% of A242 steel. It is connected to a 3-in. thick gusset plate, also…

A: PL 3/8 x 5 1/2 A242 steel3/8 in. thick gusset plate, also of A242 steel, with 3/4-inch diameter

Q: Determine the LRFD design tensile strength of the bolted connection shown. The angles are connected…

A: Given dia of bolt=16 mm fy =250 fx =405 diameter of hole=16+2 =18 mm

Q: In the connection shown in Figure 5, ASTM A572 Grade 50 steel is used for tension member (C10-20),…

A: C 10 x 25 ( A = 7.35 in2 , tw = 0.526 in )A572 grade 50 steel (Fy = 50 ksi and Fu = 65 ksi)We know…

Q: a 3" oj ob C" OC 5" of od 3" e = 4" A" B" | A" B" A" B" The holes are for 1-inch-diameter bolts.…

Q: 3. Check if the allowable modified tensile strength of bolt group under combined tensile force of…

A: Px=225 KNPy=600 KNfyb=640 N/mm2fub=800 N/mm2℧=2 Bolt M22-8.8 d=nominal diameter of bolt=22 mm

Q: Example 5.13 The connection shown in Fig. Ex. 5.13 uses 20 mm diameter 10.9S grade bolts with…

A: Given that :

Q: GIVEN: PL ⅜ x 5 ½ of A242 steel ⅜ - inch thick gusset plate A242 steel ¾ - inch diameter bolts…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: Determine the avaiable 2" streugth of 34" 3" 2 A325 -N bolts in 1.25 3" 3" 1.25" the lap splice with

A: The given data is: A 325-N bolts-with 3/4 diameter. The dimensions of the section is shown in…

Q: Problem 2: For the Channel as shown in the figure below determine the design and allowable strength.…

A: We have to determine the value of design and allowable strength. The holes are for 18 mm diameter…

Q: 3. Based on the figure below, are the threads to be considered included on the shear plane? Why?…

A: From the figure it can be observed that the shank (shown in figure below) of the bolt is ending…

Q: Two plates each with thickness t = 10 mm are bolted together with 6 - 16 mm diameter bolts forming a…

A: The thickness of the plates = 10 mm The connection provided = 6-16 mm bolts The yield strength of…

Q: The L7 x 4 x 1/2 single angle has two lines of bolts in the long leg as shown (See Figure). The U…

A: The distance from the centroid of the connected area to the plane of the connection, x=0.910 in The…

Q: A 20'-0" long tension member is fabricated by splicing together a 10'-0" length of a W14x82 (A992)…

A: The bolt shear capacity is the maximum load that a bolt can withstand in shear before failure.The…

Q: 3. A36 steel and 7/8 in diameter bolts [ 2-MC12 × 40 ㅇㅇㅇ All 2 in 2 - in 32 in 31 in 2 - in

Q: For the splice connection shown in the figure, a. Check all spacing and edge-distance…

Q: Find the available strength of the S-shape shown in Figure 3.20. The holes are for 3/4-inch-diameter…

A: Given : The S shape is shown below : Dia of holes = 3/4 in. Using A36 steel FInd - The Available…

Q: Determine the LRFD design strength and the ASD allowable strength of sections given. Neglect block…

A: Answer We know that minimum strength given by gross section yielding or Net section ruture strength…

Q: Determine the LRFD design strength and the ASD allowable strength. Neglect block shear. A36 steel…

Q: 1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threads…

A: The width of the plate is B=12 in. The thickness of the plate is t=58 in. The diameter of the bolt…

Q: Determine the smallest net area of the tension member shown in the figure. The holes are for 3/4-in…

A: here given double angle sec so please keep this in mind for no. of bolt in net area calculations…

Question

What is the Nominal Shear Capacity of the following shear splice
3/4" A325N bolts
W18x35
W24x55
-1 1/2"
1/4" A36 plate
on both sides
-1 1/2"
1"
13@

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please help !!
A double lap splice connection shown in figure B is made up of 6mm x 150mm and 9mm x 150mm. Use NSCP specifications and assume a double row of bolts with standardsize holes for a bearing type connection with threads excluded from the shear planes.Minimum tensile strength Fu = 552.93MPa. Assume diameter hole is 3mm bigger than thediameter of bolts. Allowable shear stress is Fv = 207MPa. Allowable bearing stress fb = 1.2Fu.Diameter of bolts is 19mm. Fy = 449.25MPa.(a) Compute the tensile capacity of the steel plates. (Max. Net Area = 0.85 of Gross Area)(b) Compute the number of 19mm diameter bolts to develop the full strength of the plates. Note: SHOW DRAWINGS AND SOLUTIONS.
What will be minimum number of bolts required in each row for a suitable bolted bracket connection of an ISHT 75 section attached to the flange of a ISBH 300 @ 577 N/m to carry a vertical factored load of 600 kN at an eccentricity of 60 mm as shown in the figure? Take design strength of bolt as 65.19 kN. [Assume pitch P= 60 mm] P O O
The design shear strength phi rnv of one A325 X-bolt, 1 1/8 inch in diameter (Group A, X type) in double shear is equal to: Group of answer choices 112 kips 125 kips 74.2 kips 101 kips
Which of the following gives the minimum number bolts that can be accommodated in one row of a 350mm flat plate. O 4 O 5 O 6 O 7
Help pls. Ill upvote :)
A C15x40 channel section is bolted to a gusset plate is used to resist a tensile loadPu =313 k. The bolts are 3/4 inch  diameter bolts A325 N (Group A, N Type) used insingle shear to resist this load. The bolts are to be symmetric and arranged in 3 rows.1) Determine the number of bolts needed for this connection. Draw a detailshowing how the bolts are arranged and showing spacing and edge distances onthis connection. Assume edge distance Le = 1.75db , use Le to nearest 1/4 in.2) If the connection is to be replaced by a fillet welded connection with transversewelds only along the channel web, determine the required fillet size to thenearest 16th of an inch.
1. An L 178 x 102 x 19 with one line of 20mm diameter bolts in each leg in usual gage as shown. Assume the connection length is 450mm. The pitch distance for the subsequent standard size holes is 75mm. Use ASTM A572M Grade 345 steel materials and : a. Determine the design strength of the member. b. Specify the maximum permitted length of the member as per AISC specifications.) 102mm g g 19mm 178mm L 178 x 102 x 19 Gusset Plate
Please answer with complete details. Thank you. A = 1 B = 1 C = 2
Consider the following bolted connection. Slippage is permitted. Member: L6x6x3/4 3/16 “ gusset plate Pu Pu A36 steel 3.5* 1"diameter A325-X bolts 1 1/4" 3 " 3* 1 1/4" Question 3.1: Please, indicate if the combined bolt shear strength is closer to: Question 3.2: Please, indicate if the combined bolt bearing strength is closer to: Question 3.3: Please, indicate if the angle yielding strength is closer to: Question 3.4: Please, indicate if the angle fracture strength is closer to: Question 3.5: Please, indicate if the angle block shear strength is closer to: Question 3.6: Please, indicate if the overall connection strength is closer to:
the design shear strength phi rnv of one A325-X bolt (Group A, X type), 7/8 inch in diameter in double shear is equal to: 46.8 kips 30.7 kips 27.9 kips or 61.3 kips
1