What will be minimum number of bolts required in each row for a suitable bolted bracket connection of an ISHT 75 section attached to the flange of a ISBH 300 @ 577 N/m to carry a vertical factored load of 600 kN at an eccentricity of 60 mm as shown in the figure? Take design strength of bolt as 65.19 kN. [Assume pitch P = 60 mm] O oC

What will be minimum number of bolts required in each row for a suitable bolted bracket connection of an ISHT 75 section attached to the flange of a ISBH 300 @ 577 N/m to carry a vertical factored load of 600 kN at an eccentricity of 60 mm as shown in the figure? Take design strength of bolt as 65.19 kN. [Assume pitch P = 60 mm] O oC

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.6.4P

See similar textbooks

Similar questions

10 – 7/8" Bolts Gusset Plate Plate thickness t = ½" 2" b. 2" Tension Member A36 Steel Plate 2" P 12" 2" g I 2" Calculate Tension Capacity 2" of line 1. abcde (A,„) 2. abfcgde (A„) 3. abfgde (A,), and 4. Yielding over Agross An A 3" 3"
Question 17 2L5x3x7mm tension momber is connocted to a gussot plate by 16-mm-diameter bolts as shown in the figure, Given that e= 30 mm, s= 50 mm, Fy =345 MPa and Fu=402 MPa, caicukato the following 2 L5 x3x % LLBD (two angles, long legs back-to-back) A242 stoel 60 mm e (am) (mn) e (mm) 55 Not area in shoar for a single angle under block shear lailue, Ariv mm? 56. Not area in tension for a single anglo under.block shoar failuto Arit = 57. Norninal block shear strongth in kN of the double angle Use Ups 10, Pn INPUT ALL ANSWERS AS WHOLE NUMBER
A) The 3/4 in x 15 in plate has 4 rows (or horizontal lines) of bolts. Each row has 3 bolts. The bolt diameter is 7/8 in. Determine the gross area (Ag) and the net area (An) 3/4 15 O O O O O O Q O O 3" 3 27 3 784 Bolts Pet *
Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The angle is ASTM A36 steel. X = 0.7 Y = 3.8 Z=1/2 Round your answer to 2 decimal places. Your Answer: Incorrect The answer is 77.15 ± 1%. 1/2" X" bolts 1½" Gusset plate -L3 X 3 X Z Tu I
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts T12 mm te12 mm P 300 75 75 75 Edge distances = 75 mm %3D dnole for tensile and rupture = dp +3 mm %3D dnole for bearing strength for Lec = d + 1.5 mm Fy = 248 MPa Fu = 400 MPa %3D En 330 MPa %3D Use LRFD design method. Determine the design strength due to tensile rupture strength of plates. (kN)
P-016 Given: R=4m W = 3 kN/m Allowable bolt shear stress, fv = 135 MPa Bolts at "a" and "b" are in single shear. Bolt "c" is in double shear. O O O O 8.94 O What is the required bolt diameter at B in mm? * 10.45 6.32 5.22 13.66 B A 8.50 W = 3 kN/m R=4 Compute the reaction at A in kiloNewtons. *
O cd O efgh O ij O klmn O qrst V What is the line of action of which the section will yield in tension? All holes are the same diameter. O aflrsmgb O op t P n j h C d
5. a bolted lap joint shown in the figure below. The bolts are 20m in diameter in 23 mm holes. The plates are 12m thick X350 Allowable stress of Plates: Tenaion in gross area0.60Fy Tension in net area0.50 Fu Shear on Net Area 0.30Fu Yield Strength of plate, Fy 248 Npa Ultinate tensile strength of Plate. Fu400 Mpa x, Find the safe load P based on a- Gross area yielding b. net area rapture c. block shear 2 of 3
Hhello, Thanks a lot for your help, please I have the following points: 1-Is it allowed to use Fult=65 ksi? 2-Why we consider Wt section? this procedure as I understand is applied when the connection is to flange. 3-The net area estimated is only for one bolt, i believe An=11.80-(4*7/8*0.305)=10.733 inch^2. 4-x bar which I consider is from case 2 only since case 7 will not work, x bar is only Tw/2 value?. U value=1-(0.1525/6.50)=0.977. Could you please advise? Thanks.
Problem 6: Assume that the pieces making up the connection are adequate, and very stiff such that prying forces can be disregarded, and that the nominal tensile stresses on the M20-F2280 bolts govern. The service load shown consists of 25% dead load and 75% live load. Use LRFD. 1 || T = 620 kN Calculate the factored load applied to the connection shown. Calculate the nominal tensile strength of one bolt. How many bolts are required to resist the load? I I I T = 620 kN
The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
Question 3 Determine the capacity of plate as well as below connection based on Balts (4) in the below Following reactions :- 7 11 A325, $4 þ Bolts use! Use: AISC manual U Moment = 10 kip-67 2 kip (2) Shear (3) Axial 2 kip رب Ź Plate (A 36) 10 " x 10" x ≤ 11 8 HSS. их их nxuxt 4 H² 7