7. The stress-strain diagram for polyester resin is shown in the figure. Both strut AB and column CD, madefrom this material, support the rigid beam AC. Calculate the angle of tilt of the beam when it is subjectedto load P = 60 kN. The diameter of the strut is 50 mm and the diameter of the column is 80 mm.Answer: 0 = 0.327² (MP)100956050compression2mtension➡e (mm/mm)0.01 0.02 0.03 0.048. The compound bar carries the loads of P and 2P as shown. Determine the maximum value of P thatwill satisfy the following requirements: allowable normal stress for steel is 35 ksi, allowable normal stressfor aluminum is 18 ksi, and allowance for total deformation is 0.15 inch. Answer: P = 3.60 kips2PAluminumA=0.6 inE-10 x 10 piSteelA-0.4 in2E-29 x 10 pi

Since you have asked multiple question, we will solve the only one question for you. If youwant any…

8. The compound bar carries the loads of P and 2P as shown. Determine the maximum value of P that will satisfy the following requirements: allowable normal stress for steel is 35 ksi, allowable normal stress for aluminum is 18 ksi, and allowance for total deformation is 0.15 inch. Answer: P= 3.60 kips 2P Steel Aluminum A-06 in E-10 x 10 pi A-0.4 in E-29 x 10° pi

8. The compound bar carries the loads of P and 2P as shown. Determine the maximum value of P that will satisfy the following requirements: allowable normal stress for steel is 35 ksi, allowable normal stress for aluminum is 18 ksi, and allowance for total deformation is 0.15 inch. Answer: P= 3.60 kips 2P Steel Aluminum A-06 in E-10 x 10 pi A-0.4 in E-29 x 10° pi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A stepped circular bar having diameters 20 mm, 15: mm and 10 mm over axial lengths of 100 mm, 80mm and 60mm is subjected to an axial tensile force of 5 KN. If E= 100 x 103 N/mm2 and 1/m = 0.32 for the material of bar, determine total change in length and change in each diameter.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 12 mm and an allowable normal stress of 80 MPa. Pipe (2) has an outside diameter of 50 mm, a wall thickness of 7 mm, and an allowable normal stress of 80 MPa. Assume x₁ = 3.7 m, x₂ = 1.2 m, and y₁ = 4.0 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. 9₁ (1) Answer: Pmax= B (2) 3° P C kN 2
SN= 50 lbs FN= 104 kips
Q no 108 sorry for that first I consider fig with 207. But it is not with 207 it is with Q.No 208. Please solve it I will great thankfull to you
Determine the allowable stress in last example if the factor of safety is 2.5.
A metal bar is made out of A-36 steel and has a diameter d = 23mm with the end at A fixed to the wall. There is are balanced axial loads at B of P₁ = 30 kN and a point load at C 35 kN. The distance from A to B is L₁ of P2 570 mm 390 mm. Calculate the = and the distance from B to C is L2 displacement of point C relative to point A. A L₁ ↑ d B L2 - P₁₁ Р1 С The displacement at C is 8 = -0.00306 d - cc 080 BY NO SA 2021 Cathy Zupke P₂ x mm
The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ allowable= 243 ksi for pin material.
The bell-crank mechanism is in equilibrium for an applied load of P = 47 kN. Assume that a = 300 mm, b = 225 mm, and 0 = 57°. The pin at B has a diameter of d = 14 mm, and the bell crank has a thickness of t = 8 mm. Calculate the bearing stress in the bell crank at pin B. (1) P Answer: Bell crank A O= i 34.21 a с MPa B Support bracket b F₁ IF B
If load P = 22.9 kips, determine the normal force in bar (1). D P A 6 ft 51.9 kips 44.8 kips 27.3 kips 38.2 kips O 40.4 kips B (1) 4 ft
What is the minimum clearance allowed for meshing spur gears with diametral pitch of 20? The spur gear has 25 teeth.
DRAW THE FBD FOR THIS PROBLEM. PLEASE PROVIDE DETAILED SOLUTION FOR THIS PROBLEM
pls help